[PATCH] pinctrl: Add one-register-per-pin type device tree based pinctrl driver
Tony Lindgren
tony at atomide.com
Mon Jun 18 15:50:36 EST 2012
* Stephen Warren <swarren at wwwdotorg.org> [120615 09:21]:
> On 06/15/2012 03:49 AM, Tony Lindgren wrote:
>
> (Arnd, Grant, Rob, CC'ing you mainly re: the very last set of comments
> in this email; can you take a look at Tony's patch and comment on the
> binding)
Yes please take a look.
> > Care to clarify a bit what you had in mind there?
>
> Basically I meant:
>
> 1) Remove anything TI-/OMAP-specific from the generic binding document
>
> 2) For any TI-/OMAP-specific additions, create a binding document that
> describes those separately to the generic binding documentation.
>
> However, given that there are no TI-/OMAP-specific additions; OMAP2 just
> uses the base generic bindings exactly as defined, I don't think you
> actually need to create an TI-/OMAP-specific document, since there's
> nothing for it to document.
OK so basically you just want the pinctrl-single binding document to be
generic. Yes I'll do that.
> > It's best to describe the hardware in case we need to set up some hardware
> > specific things in the driver.
>
> There's a difference between the (set of) compatible value(s) that
> appears in the .dts file, and the compatible value(s) that the driver
> binds to.
>
> Since this driver is purely implementing the pinctrl-single binding, I
> believe only that should be listed in the driver's of_match table.
>
> However, since the .dts file is describing HW that is both a specific
> OMAP instance, and compatible with pinctrl-single, the .dts file can
> certainly list both. If in the future, the driver ever needs to
> specifically know the difference between the specific OMAP versions, or
> OMAP-vs-something-else, the compatible value will be there already in
> the .dts file, so this will all work. However, I'd argue that if the
> driver has to ever know that, it's probably not appropriate to say it's
> compatible with pinctrl-single any more...
Yes OK I see what you mean now. Sounds good to me, and if/when we need
some hardware specific things, we'll add specific parsing for the other
compatible values.
> >> One final comment: A little while before Linaro Connect in San
> >> Francisco, we were all having difficulty coming up with any kind of DT
> >> binding for pinctrl. I had suggested the possibility of creating a
> >> binding which just said "write value X to register Y, write value P to
> >> register Q, ...". This was rejected at connect, because a raw list of
> >> register writes didn't document anything or describe semantics - it was
> >> too much of a binary blob. This driver seems to be doing almost the
> >> exact same thing. In order to avoid that assertion, it'd need to truly
> >> have individual representations of which pins exist, which pingroups
> >> exist, which functions exist, and which functions can be selected onto
> >> which pins/pingroups. That would be a radically different binding. I
> >> wonder what's changed such that this kind of driver wasn't acceptable
> >> then, but is now?
> >
> > Well that's why I had two bindings earlier: The current binding for the
> > bulk pins that's faster to parse, and a more verbose binding for drivers that
> > allows naming the functions.
> >
> > In your previous comments at [1] you seemed to prefer this current binding
> > based on the "Why not only allow (1)?" comment. Maybe you had something else
> > in mind, care to clarify that a bit too?
>
> Well, first I thought about semantics vs. just banging a register list a
> tiny bit more, and remembered the previous discussion.
>
> But my comment at [1] wasn't so much about "why not just have a raw
> register list", but more regarding why support two different
> representations within the same binding; it wasn't really clear to me
> from reading the original email what the difference between the two
> representations; why have two representations, why/when-to use one vs.
> the other, that the difference was about providing a "semantic" list of
> pins/pingroups/functions vs. providing a "raw" register list.
I too would prefer more verbose .dts files. Unfortunately the parsing of
several hundred board specific pins adds quite a bit of overhead.
> IIRC, the pushback on a raw "bang these registers" representation came
> from Grant and/or Arnd. It'd be a good idea if they (and indeed Rob)
> could comment on this binding proposal. If they're OK with this kind of
> pretty raw representation, I'm not going to object, but I have a feeling
> they might not like it?
Yes let's see if anybody has better ideas.
Regards,
Tony
> > [1] http://article.gmane.org/gmane.linux.kernel/1291838
More information about the devicetree-discuss
mailing list