[PATCH V3 1/2] of: Add generic device tree DMA helpers

Vinod Koul vinod.koul at linux.intel.com
Fri Jul 20 14:00:50 EST 2012


On Tue, 2012-07-17 at 19:24 +0000, Arnd Bergmann wrote:
> On Friday 13 July 2012, Vinod Koul wrote:
> > > Do you mean there must be a global table, or are you ok with putting
> > > the information about a channel into the device that uses the channel,
> > > as we do for most other subsystems (IRQ, GPIO, pinctrl, ...).
> > > If not, what is the problem with that approach?
> > 
> > Today, we simple ask, "give me dma channel with DMA_SLAVE capability".
> > 
> > If we change it to "give me dma channel which suits my need" and have
> > additional information in dmaengine to handle this request effectively.
> > 
> > What that would mean is
> > a) DMA channel either knows which channel to provide, Or
> > b) Additional arguments provided to dmaengine API to help it find out
> > which channel to provide.
> > 
> > It would be good to have client ask for a specific channel. But in order
> > to build generic clients, we face a problem that clients may not know
> > how they mapped to dmac by SoC designer. Or the mux maybe entirely
> > flexible on which channel.
> > 
> > If we add this as DT property (which I assume should be platform
> > specific), then client will know which channel to request.
> > It can have two levels, dmac and channel. In case mux is flexible enough
> > then client gets a channel and program the mux for this mapping.
> > 
> > I think this is the most simplistic solution I have for this, thoughts?
> 
> I think we're basically on the same page. Let's see if I have covered
> all the cases we discussed so far. I've tried to update the binding that
> Jon sent out initially with everything we've discussed, so please review
> this to see if I understood you correctly.
I think this looks fine to me. Few comments below on client side
> 
> 	Arnd
> 
> 
> * Generic DMA Controller and DMA request bindings
> 
> Generic binding to provide a way for a driver using DMA Engine to retrieve the
> DMA request or channel information that goes from a hardware device to a DMA
> controller.
> 
> * DMA controller
> 
> Required property:
>     - #dma-cells: Number elements to describe DMA channel information. Must be
>                   at least 2, allowing a phandle and a flags cell, but usually
> 		  is larger so a client can also specify a request or channel
>                   number and/or some configuration.
> 
> Optional properties:
>     - #dma-channels: Number of DMA channels supported by the controller.
>     - #dma-requests: Number of DMA requests signals supported by the controller.
> 
> Example:
> 
>        sdma: dmaengine at 48000000 {
>                compatible = "ti,omap4-sdma"
>                reg = <0x48000000 0x1000>;
>                interrupts = <4>;
>                #dma-cells = <3>;
>                #dma-channels = <32>;
>                #dma-requests = <127>;
>        };
> 
> 
> * DMA client
> 
> Client drivers should specify the DMA property using a phandle to the controller
> followed by the number of DMA request/channel and the transfer type of the
> channel (eg. device-to-memory, memory-to-device, memory-to-memory, etc).
> 
> Required property:
>     dmas: list of one or more dma specifiers, each consisting of
>      - phandle pointing to dma controller node
>      - flags word, a bit map that can hold these flags
>        * 0x00000001 channel can be used for transfer from device
>        * 0x00000002 channel can be user for transfer to device
Is this for identifying which channel is for TX and RX? If not I am not
sure I understood it well

>      - zero or more cells in a format specific to the the dma controller
>        node listed in the phandle. This typically contains a dma request
>        line number or a channel number, but can contain any data that
>        is used required for configuring a channel.
> 
> Optional property:
>     dma-names: when present, this shall contain one identifier string
>     for each dma specifier in the dmas property. The specific strings
>     that can be used are defined in the binding of the DMA client
>     device. When multiple dma specifiers can be used as alternatives,
>     the dma-names for those dma specifiers must be identical.
> 
> Any dma specifiers that have identical flags and identical dma-names
> (if present) shall refer to different dma controllers that can be
> used as alternatives, e.g. when a request line is connected to
> multiple dma controllers. If multiple dma specifiers are listed that
> have the same flags but refer to different functional channels,
> the dma-names property must be used to distinguish them.
> 
> Examples:
> 
> 1. One DMA write channel, one DMA read/write channel:
> 
>        i2c1: i2c at 1 {
>                ...
>                dmas = <&sdma 2 1 &sdma 3 2>;
>                ...
>        };
> 
> 2. A single read-write channel with two alternative dma controllers
>    providing it:
> 
> 	dmas = <&dma0 3 5
> 		&dma1 3 7
> 		&dma2 3 2>;
> 
> 3. A device with three channels, one of which has two alternatives:
> 
> 	dmas = <&dma0 1 4 /* data read */
> 		&dma0 2 6 /* data write */
> 		&dma1 1 0 /* error read */
> 		&dma2 1 0>; /* alternative error read */
> 	dma-names = "data", "data", "error", "error";
> 
> 4. A dma controller requiring complex configuration:
> 
>        dma: dmaengine at 48000000 {
>                compatible = "foo,foo-sdma"
>                reg = <0x48000000 0x1000>;
>                interrupts = <4>;
>                #dma-cells = <6>; /* phandle, flag, request, channel,
> 					 input-width, output-width */
Why would we want the widths to be here?
Assuming a DMA from System memory to a peripheral, source width should
be system memory width and destination the peripheral width. IMO these
should not be in dma property even if we need these
>                #dma-channels = <32>;
>                #dma-requests = <127>;
>        };
> 
>        mmc at 49000000 {
> 		...
> 		dmas = <&dma 1	/* read */
> 			2	/* request line */
> 			5       /* channel */
> 			16	/* 16 bit bus width on read */
> 			8>	/* 8 bit bus width on write */
> 		       <&dma 2	/* write */
> 			3	/* request line */
> 			6       /* channel */
> 			8	/* 8 bit bus width on read */
> 			16>	/* 16 bit bus width on write */
>From this looks like flag is for TX/RX, so maybe i read correct :)

-- 
~Vinod



More information about the devicetree-discuss mailing list