[PATCH v4 09/11] drivers: usb: musb: Add device tree support for omap musb glue

ABRAHAM, KISHON VIJAY kishon at ti.com
Fri Jul 20 00:48:27 EST 2012


Hi,

On Thu, Jul 19, 2012 at 6:51 PM, Gupta, Ajay Kumar <ajay.gupta at ti.com> wrote:
> Hi,
>> Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
>> ---
>>  Documentation/devicetree/bindings/usb/omap-usb.txt |   34 ++++++++++++-
>>  drivers/usb/musb/omap2430.c                        |   55
>> ++++++++++++++++++++
>>  2 files changed, 88 insertions(+), 1 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt
>> b/Documentation/devicetree/bindings/usb/omap-usb.txt
>> index 80a28c9..39cdffb 100644
>> --- a/Documentation/devicetree/bindings/usb/omap-usb.txt
>> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
>> @@ -1,4 +1,4 @@
>> -OMAP USB PHY
>> +OMAP USB PHY AND GLUE
>>
>>  OMAP USB2 PHY
>>
>> @@ -14,3 +14,35 @@ usb2phy at 0x4a0ad080 {
>>       compatible = "ti,omap-usb2";
>>       reg = <0x4a0ad080 0x58>;
>>  };
>> +
>> +OMAP MUSB GLUE
>> + - compatible : Should be "ti,musb-omap2430"
>> + - ti,hwmods : must be "usb_otg_hs"
>> + - multipoint : Should be "1" indicating the musb controller supports
>> +   multipoint. This is a MUSB configuration-specific setting.
>> + - num_eps : Specifies the number of endpoints. This is also a
>> +   MUSB configuration-specific setting. Should be set to "16"
>> + - ram_bits : Specifies the ram address size. Should be set to "12"
>> + - interface_type : This is a board specific setting to describe the type
>> of
>> +   interface between the controller and the phy. It should be "0" or "1"
>> +   specifying ULPI and UTMI respectively.
>> + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
>> +   represents PERIPHERAL.
>> + - power : Should be "50". This signifies the controller can supply upto
>> +   100mA when operating in host mode.
>> +
>> +SOC specific device node entry
>> +usb_otg_hs: usb_otg_hs at 4a0ab000 {
>> +     compatible = "ti,musb-omap2430";
>> +     ti,hwmods = "usb_otg_hs";
>> +     multipoint = <1>;
>> +     num_eps = <16>;
>> +     ram_bits = <12>;
>> +};
>> +
>> +Board specific device node entry
>> +&usb_otg_hs {
>> +     interface_type = <1>;
>> +     mode = <3>;
>> +     power = <50>;
>> +};
>> diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
>> index addbebf..331e477 100644
>> --- a/drivers/usb/musb/omap2430.c
>> +++ b/drivers/usb/musb/omap2430.c
>> @@ -30,6 +30,7 @@
>>  #include <linux/init.h>
>>  #include <linux/list.h>
>>  #include <linux/io.h>
>> +#include <linux/of.h>
>>  #include <linux/platform_device.h>
>>  #include <linux/dma-mapping.h>
>>  #include <linux/pm_runtime.h>
>> @@ -469,8 +470,11 @@ static u64 omap2430_dmamask = DMA_BIT_MASK(32);
>>  static int __devinit omap2430_probe(struct platform_device *pdev)
>>  {
>>       struct musb_hdrc_platform_data  *pdata = pdev->dev.platform_data;
>> +     struct omap_musb_board_data     *data;
>>       struct platform_device          *musb;
>>       struct omap2430_glue            *glue;
>> +     struct device_node              *np = pdev->dev.of_node;
>> +     struct musb_hdrc_config         *config;
>>       struct resource                 *res;
>>       int                             ret = -ENOMEM;
>>
>> @@ -500,6 +504,43 @@ static int __devinit omap2430_probe(struct
>> platform_device *pdev)
>>       if (glue->control_otghs == NULL)
>>               dev_dbg(&pdev->dev, "Failed to obtain control memory\n");
>>
>> +     if (np) {
>> +             pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
>> +             if (!pdata) {
>> +                     dev_err(&pdev->dev,
>> +                             "failed to allocate musb platfrom data\n");
>> +                     ret = -ENOMEM;
>> +                     goto err1;
>> +             }
>> +
>> +             data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
>> +             if (!data) {
>> +                     dev_err(&pdev->dev,
>> +                                     "failed to allocate musb board data\n");
>> +                     ret = -ENOMEM;
>> +                     goto err1;
>> +             }
>> +
>> +             config = devm_kzalloc(&pdev->dev, sizeof(*config), GFP_KERNEL);
>> +             if (!data) {
>> +                     dev_err(&pdev->dev,
>> +                             "failed to allocate musb hdrc config\n");
>> +                     goto err1;
>> +             }
>> +
>> +             of_property_read_u32(np, "mode", (u32 *)&pdata->mode);
>> +             of_property_read_u32(np, "interface_type",
>> +                                             (u32 *)&data->interface_type);
>> +             of_property_read_u32(np, "num_eps", (u32 *)&config->num_eps);
>> +             of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits);
>> +             of_property_read_u32(np, "mode", (u32 *)&pdata->mode);
>
> pdata->mode is already read so above should be removed.

Ok.

Thanks
Kishon


More information about the devicetree-discuss mailing list