[PATCH V2 1/7] ARM: SAMSUNG: add additional registers and SFR definitions for writeback
Leela Krishna Amudala
l.krishna at samsung.com
Thu Jul 19 22:43:49 EST 2012
Hello Marek,
On Wed, Jul 18, 2012 at 12:21 PM, Marek Szyprowski
<m.szyprowski at samsung.com> wrote:
> Hello,
>
> On Wednesday, July 18, 2012 7:57 AM Leela Krishna Amudala wrote:
>
>> This patch updates the register address offsets and adds SFR definitions
>> for writeback for Samsung's V8 display controller.
>>
>> Signed-off-by: Leela Krishna Amudala <l.krishna at samsung.com>
>> ---
>> arch/arm/plat-samsung/include/plat/regs-fb-v4.h | 10 ++++
>> arch/arm/plat-samsung/include/plat/regs-fb.h | 51 +++++++++++++++++++++++
>> drivers/video/Kconfig | 6 +++
>> 3 files changed, 67 insertions(+), 0 deletions(-)
>>
>> diff --git a/arch/arm/plat-samsung/include/plat/regs-fb-v4.h b/arch/arm/plat-
>> samsung/include/plat/regs-fb-v4.h
>> index 4c3647f..1639c17 100644
>> --- a/arch/arm/plat-samsung/include/plat/regs-fb-v4.h
>> +++ b/arch/arm/plat-samsung/include/plat/regs-fb-v4.h
>> @@ -30,9 +30,16 @@
>> #define VIDCON1_FSTATUS_EVEN (1 << 15)
>>
>> /* Video timing controls */
>> +#ifdef CONFIG_FB_EXYNOS_FIMD_V8
>> +#define VIDTCON0 (0x20010)
>> +#define VIDTCON1 (0x20014)
>> +#define VIDTCON3 (0x2001C)
>> +#else
>> #define VIDTCON0 (0x10)
>> #define VIDTCON1 (0x14)
>> #define VIDTCON2 (0x18)
>> +#define VIDTCON3 (0x1C)
>> +#endif
>>
>> /* Window position controls */
>>
>> @@ -43,9 +50,12 @@
>> #define VIDOSD_BASE (0x40)
>>
>> #define VIDINTCON0 (0x130)
>> +#define VIDINTCON1 (0x134)
>>
>> /* WINCONx */
>>
>> +#define WINCONx_CSC_CON_EQ709 (1 << 28)
>> +#define WINCONx_CSC_CON_EQ601 (0 << 28)
>> #define WINCONx_CSCWIDTH_MASK (0x3 << 26)
>> #define WINCONx_CSCWIDTH_SHIFT (26)
>> #define WINCONx_CSCWIDTH_WIDE (0x0 << 26)
>> diff --git a/arch/arm/plat-samsung/include/plat/regs-fb.h b/arch/arm/plat-
>> samsung/include/plat/regs-fb.h
>> index 9a78012..6d2ee16 100644
>> --- a/arch/arm/plat-samsung/include/plat/regs-fb.h
>> +++ b/arch/arm/plat-samsung/include/plat/regs-fb.h
>> @@ -32,12 +32,28 @@
>>
>> #define VIDCON0 (0x00)
>> #define VIDCON0_INTERLACE (1 << 29)
>> +
>> +#ifdef CONFIG_FB_EXYNOS_FIMD_V8
>> +#define VIDOUT_CON (0x20000)
>> +#define VIDOUT_CON_VIDOUT_UP_MASK (0x1 << 16)
>> +#define VIDOUT_CON_VIDOUT_UP_SHIFT (16)
>> +#define VIDOUT_CON_VIDOUT_UP_ALWAYS (0x0 << 16)
>> +#define VIDOUT_CON_VIDOUT_UP_START_FRAME (0x1 << 16)
>> +#define VIDOUT_CON_VIDOUT_F_MASK (0x7 << 8)
>> +#define VIDOUT_CON_VIDOUT_F_SHIFT (8)
>> +#define VIDOUT_CON_VIDOUT_F_RGB (0x0 << 8)
>> +#define VIDOUT_CON_VIDOUT_F_I80_LDI0 (0x2 << 8)
>> +#define VIDOUT_CON_VIDOUT_F_I80_LDI1 (0x3 << 8)
>> +#define VIDOUT_CON_VIDOUT_F_WB (0x4 << 8)
>> +#endif
>> +
>> #define VIDCON0_VIDOUT_MASK (0x3 << 26)
>> #define VIDCON0_VIDOUT_SHIFT (26)
>> #define VIDCON0_VIDOUT_RGB (0x0 << 26)
>> #define VIDCON0_VIDOUT_TV (0x1 << 26)
>> #define VIDCON0_VIDOUT_I80_LDI0 (0x2 << 26)
>> #define VIDCON0_VIDOUT_I80_LDI1 (0x3 << 26)
>> +#define VIDCON0_VIDOUT_WB (0x4 << 26)
>>
>> #define VIDCON0_L1_DATA_MASK (0x7 << 23)
>> #define VIDCON0_L1_DATA_SHIFT (23)
>> @@ -81,7 +97,13 @@
>> #define VIDCON0_ENVID (1 << 1)
>> #define VIDCON0_ENVID_F (1 << 0)
>>
>> +#ifdef CONFIG_FB_EXYNOS_FIMD_V8
>> +#define VIDOUT_CON (0x20000)
>> +#define VIDCON1 (0x20004)
>> +#else
>> #define VIDCON1 (0x04)
>> +#endif
>> +
>> #define VIDCON1_LINECNT_MASK (0x7ff << 16)
>> #define VIDCON1_LINECNT_SHIFT (16)
>> #define VIDCON1_LINECNT_GET(_v) (((_v) >> 16) & 0x7ff)
>> @@ -111,6 +133,14 @@
>> #define VIDCON2_TVFMTSEL1_RGB (0x0 << 12)
>> #define VIDCON2_TVFMTSEL1_YUV422 (0x1 << 12)
>> #define VIDCON2_TVFMTSEL1_YUV444 (0x2 << 12)
>> +#define VIDCON2_TVFMTSEL1_SHIFT (12)
>> +#define VIDCON2_TVFMTSEL_SW (1 << 14)
>> +#define VIDCON2_TVFORMATSEL_YUV444 (0x2 << 12)
>> +
>> +#define VIDCON2_TVFMTSEL1_MASK (0x3 << 12)
>> +#define VIDCON2_TVFMTSEL1_RGB (0x0 << 12)
>> +#define VIDCON2_TVFMTSEL1_YUV422 (0x1 << 12)
>> +#define VIDCON2_TVFMTSEL1_YUV444 (0x2 << 12)
>>
>> #define VIDCON2_ORGYCbCr (1 << 8)
>> #define VIDCON2_YUVORDCrCb (1 << 7)
>> @@ -165,8 +195,15 @@
>> #define VIDTCON1_HSPW_SHIFT (0)
>> #define VIDTCON1_HSPW_LIMIT (0xff)
>> #define VIDTCON1_HSPW(_x) ((_x) << 0)
>> +#define VIDCON1_VCLK_MASK (0x3 << 9)
>> +#define VIDCON1_VCLK_HOLD (0x0 << 9)
>> +#define VIDCON1_VCLK_RUN (0x1 << 9)
>>
>> +#ifdef CONFIG_FB_EXYNOS_FIMD_V8
>> +#define VIDTCON2 (0x20018)
>> +#else
>> #define VIDTCON2 (0x18)
>> +#endif
>> #define VIDTCON2_LINEVAL_E(_x) ((((_x) & 0x800) >> 11) << 23)
>> #define VIDTCON2_LINEVAL_MASK (0x7ff << 11)
>> #define VIDTCON2_LINEVAL_SHIFT (11)
>> @@ -186,6 +223,9 @@
>> #define WINCONx_BYTSWP (1 << 17)
>> #define WINCONx_HAWSWP (1 << 16)
>> #define WINCONx_WSWP (1 << 15)
>> +#define WINCONx_ENLOCAL_MASK (0xf << 15)
>> +#define WINCONx_INRGB_RGB (0 << 13)
>> +#define WINCONx_INRGB_YCBCR (1 << 13)
>> #define WINCONx_BURSTLEN_MASK (0x3 << 9)
>> #define WINCONx_BURSTLEN_SHIFT (9)
>> #define WINCONx_BURSTLEN_16WORD (0x0 << 9)
>> @@ -205,6 +245,7 @@
>> #define WINCON0_BPPMODE_24BPP_888 (0xb << 2)
>>
>> #define WINCON1_BLD_PIX (1 << 6)
>> +#define WINCON1_BLD_PLANE (0 << 6)
>>
>> #define WINCON1_ALPHA_SEL (1 << 1)
>> #define WINCON1_BPPMODE_MASK (0xf << 2)
>> @@ -395,9 +436,19 @@
>> #define WPALCON_W0PAL_16BPP_A555 (0x5 << 0)
>> #define WPALCON_W0PAL_16BPP_565 (0x6 << 0)
>>
>> +/* Clock gate mode control */
>> +#define REG_CLKGATE_MODE (0x1b0)
>> +#define REG_CLKGATE_MODE_AUTO_CLOCK_GATE (0 << 0)
>> +#define REG_CLKGATE_MODE_NON_CLOCK_GATE (1 << 0)
>> +
>> /* Blending equation control */
>> #define BLENDCON (0x260)
>> #define BLENDCON_NEW_MASK (1 << 0)
>> #define BLENDCON_NEW_8BIT_ALPHA_VALUE (1 << 0)
>> #define BLENDCON_NEW_4BIT_ALPHA_VALUE (0 << 0)
>>
>> +/* Window alpha control */
>> +#define VIDW0ALPHA0 (0x200)
>> +#define VIDW0ALPHA1 (0x204)
>> +#define DPCLKCON (0x27c)
>> +#define DPCLKCON_ENABLE (1 << 1)
>> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
>> index 0217f74..f81bf55 100644
>> --- a/drivers/video/Kconfig
>> +++ b/drivers/video/Kconfig
>> @@ -2053,6 +2053,12 @@ config FB_S3C
>>
>> Currently the support is only for the S3C6400 and S3C6410 SoCs.
>>
>> +config FB_EXYNOS_FIMD_V8
>> + bool "register extensions for FIMD version 8"
>> + depends on ARCH_EXYNOS5
>> + ---help---
>> + This uses register extensions for FIMD version 8
>> +
>> config FB_S3C_DEBUG_REGWRITE
>> bool "Debug register writes"
>> depends on FB_S3C
>
> Do we really need these defines in arch/arm/plat-samsung/include/plat/regs-fb* ?
> IMHO they should be moved from arch/arm to drivers/video to live together with the driver.
> They are not a part of core platform code. I thought that there have been some patches
> cleaning up regs-fb mess a long time ago, but it looks they didn't get their way to
> mainline.
>
The defines I had given in these headers are specific to exynos5
platform and are using by both drm-fimd and
s3c-fb. I'm not understanding the need to move these defines from
arch/arm to drivers/video. Can you please tell me why we have to do
that.
Best Wishes,
Leela Krishna Amudala.
> Best regards
> --
> Marek Szyprowski
> Samsung Poland R&D Center
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
More information about the devicetree-discuss
mailing list