[PATCH v2 3/4] arm/dts: OMAP4: Add mmc controller nodes and board data

T Krishnamoorthy, Balaji balajitk at ti.com
Fri Feb 24 21:59:17 EST 2012


On Fri, Feb 24, 2012 at 3:56 PM, Rajendra Nayak <rnayak at ti.com> wrote:
> On Friday 24 February 2012 03:46 PM, T Krishnamoorthy, Balaji wrote:
>>>
>>> diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
>>> index 29f4589..9204f60 100644
>>> --- a/arch/arm/boot/dts/omap4.dtsi
>>> +++ b/arch/arm/boot/dts/omap4.dtsi
>>> @@ -25,6 +25,11 @@
>>>                serial1 =&uart2;
>>>                serial2 =&uart3;
>>>                serial3 =&uart4;
>>> +               mmc1 =&mmc1;
>>> +               mmc2 =&mmc2;
>>> +               mmc3 =&mmc3;
>>> +               mmc4 =&mmc4;
>>> +               mmc5 =&mmc5;
>>>        };
>>>
>>>        cpus {
>>> @@ -155,5 +160,31 @@
>>>                        #size-cells =<0>;
>>>                        ti,hwmods = "i2c4";
>>>                };
>>> +
>>> +               mmc1: mmc at 1 {
>>> +                       compatible = "ti,omap4-hsmmc";
>>> +                       ti,hwmods = "mmc1";
>>> +                       ti,dual-volt;
>>> +               };
>>> +
>>> +               mmc2: mmc at 2 {
>>> +                       compatible = "ti,omap4-hsmmc";
>>> +                       ti,hwmods = "mmc2";
>>> +               };
>>
>>
>> Hi Rajendra,
>> Is there a way to control the device registration order,
>> eMMC connected to mmc2 needs to be registered as /dev/mmcblk0p ...
>> irrespective of whether SD card is mount or not on mmc1 card slot.
>> So that bootargs would not have to be modified when filesystem is on eMMC.
>
>
> I don't know if we can, but even if we could, we take care of the same
> bootargs working on two boards (say sdp and panda) *if* on sdp I have my
> filesystem on eMMC and on panda I have it on external card.
> What happens if I want to use my filesystem on both boards on external
> card?

While booting if SD card is present in the card slot, SD is detected
as /dev/mmcblk0
and eMMC as /dev/mmcblk1
If SD card is not present, then eMMC is detected as /dev/mmcblk0
When filesystem is in eMMC then bootargs has to switch between mmcblk0
or mmcblk1
depending on whether SD is present or not.

By changing the device order, eMMC will always be mmcblk0 independent
of SD card status.

>
>
>>
>>> +
>>> +               mmc3: mmc at 3 {
>>> +                       compatible = "ti,omap4-hsmmc";
>>> +                       ti,hwmods = "mmc3";
>>> +               };
>>> +
>>> +               mmc4: mmc at 4 {
>>> +                       compatible = "ti,omap4-hsmmc";
>>> +                       ti,hwmods = "mmc4";
>>> +               };
>>> +
>>> +               mmc5: mmc at 5 {
>>> +                       compatible = "ti,omap4-hsmmc";
>>> +                       ti,hwmods = "mmc5";
>>> +               };
>>>        };
>>>  };
>>> --
>>> 1.7.1
>>>
>


More information about the devicetree-discuss mailing list