[RFC PATCH v2 07/12] MIPS: Octeon: Rearrance CVMX files in preperation for device tree
David Daney
ddaney at caviumnetworks.com
Sat Mar 5 06:42:19 EST 2011
Signed-off-by: David Daney <ddaney at caviumnetworks.com>
---
.../cavium-octeon/executive/cvmx-helper-sgmii.c | 6 +-
.../mips/cavium-octeon/executive/cvmx-helper-spi.c | 10 ++
.../cavium-octeon/executive/cvmx-helper-xaui.c | 22 +++--
arch/mips/cavium-octeon/executive/cvmx-helper.c | 93 ++++++++++++++++---
arch/mips/include/asm/octeon/cvmx-helper-loop.h | 1 +
arch/mips/include/asm/octeon/cvmx-helper-npi.h | 1 +
arch/mips/include/asm/octeon/cvmx-helper-rgmii.h | 1 +
arch/mips/include/asm/octeon/cvmx-helper-sgmii.h | 1 +
arch/mips/include/asm/octeon/cvmx-helper-spi.h | 1 +
arch/mips/include/asm/octeon/cvmx-helper-xaui.h | 1 +
arch/mips/include/asm/octeon/cvmx-helper.h | 1 +
11 files changed, 114 insertions(+), 24 deletions(-)
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-sgmii.c b/arch/mips/cavium-octeon/executive/cvmx-helper-sgmii.c
index 464347f..0c0bf5d 100644
--- a/arch/mips/cavium-octeon/executive/cvmx-helper-sgmii.c
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-sgmii.c
@@ -326,6 +326,10 @@ static int __cvmx_helper_sgmii_hardware_init(int interface, int num_ports)
return 0;
}
+int __cvmx_helper_sgmii_enumerate(int interface)
+{
+ return 4;
+}
/**
* Probe a SGMII interface and determine the number of ports
* connected to it. The SGMII interface should still be down after
@@ -347,7 +351,7 @@ int __cvmx_helper_sgmii_probe(int interface)
mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
mode.s.en = 1;
cvmx_write_csr(CVMX_GMXX_INF_MODE(interface), mode.u64);
- return 4;
+ return __cvmx_helper_sgmii_enumerate(interface);
}
/**
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-spi.c b/arch/mips/cavium-octeon/executive/cvmx-helper-spi.c
index 02a4442..2830e4b 100644
--- a/arch/mips/cavium-octeon/executive/cvmx-helper-spi.c
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-spi.c
@@ -51,6 +51,16 @@ void __cvmx_interrupt_stxx_int_msk_enable(int index);
#define CVMX_HELPER_SPI_TIMEOUT 10
#endif
+int __cvmx_helper_spi_enumerate(int interface)
+{
+ if ((cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_SIM) &&
+ cvmx_spi4000_is_present(interface)) {
+ return 10;
+ } else {
+ return 16;
+ }
+}
+
/**
* Probe a SPI interface and determine the number of ports
* connected to it. The SPI interface should still be down after
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-xaui.c b/arch/mips/cavium-octeon/executive/cvmx-helper-xaui.c
index 667a8e3..1723248e 100644
--- a/arch/mips/cavium-octeon/executive/cvmx-helper-xaui.c
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-xaui.c
@@ -44,6 +44,19 @@
void __cvmx_interrupt_gmxx_enable(int interface);
void __cvmx_interrupt_pcsx_intx_en_reg_enable(int index, int block);
void __cvmx_interrupt_pcsxx_int_en_reg_enable(int index);
+
+int __cvmx_helper_xaui_enumerate(int interface)
+{
+ union cvmx_gmxx_hg2_control gmx_hg2_control;
+
+ /* If HiGig2 is enabled return 16 ports, otherwise return 1 port */
+ gmx_hg2_control.u64 = cvmx_read_csr(CVMX_GMXX_HG2_CONTROL(interface));
+ if (gmx_hg2_control.s.hg2tx_en)
+ return 16;
+ else
+ return 1;
+}
+
/**
* Probe a XAUI interface and determine the number of ports
* connected to it. The XAUI interface should still be down
@@ -56,7 +69,6 @@ void __cvmx_interrupt_pcsxx_int_en_reg_enable(int index);
int __cvmx_helper_xaui_probe(int interface)
{
int i;
- union cvmx_gmxx_hg2_control gmx_hg2_control;
union cvmx_gmxx_inf_mode mode;
/*
@@ -90,13 +102,7 @@ int __cvmx_helper_xaui_probe(int interface)
pko_mem_port_ptrs.s.pid = interface * 16 + i;
cvmx_write_csr(CVMX_PKO_MEM_PORT_PTRS, pko_mem_port_ptrs.u64);
}
-
- /* If HiGig2 is enabled return 16 ports, otherwise return 1 port */
- gmx_hg2_control.u64 = cvmx_read_csr(CVMX_GMXX_HG2_CONTROL(interface));
- if (gmx_hg2_control.s.hg2tx_en)
- return 16;
- else
- return 1;
+ return __cvmx_helper_xaui_enumerate(interface);
}
/**
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper.c b/arch/mips/cavium-octeon/executive/cvmx-helper.c
index 6238a22..bea6ab6 100644
--- a/arch/mips/cavium-octeon/executive/cvmx-helper.c
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper.c
@@ -234,21 +234,16 @@ static int __cvmx_helper_port_setup_ipd(int ipd_port)
}
/**
- * This function probes an interface to determine the actual
- * number of hardware ports connected to it. It doesn't setup the
- * ports or enable them. The main goal here is to set the global
- * interface_port_count[interface] correctly. Hardware setup of the
- * ports will be performed later.
+ * This function sets the interface_port_count[interface] correctly,
+ * without modifying any hardware configuration. Hardware setup of
+ * the ports will be performed later.
*
* @interface: Interface to probe
*
* Returns Zero on success, negative on failure
*/
-int cvmx_helper_interface_probe(int interface)
+int cvmx_helper_interface_enumerate(int interface)
{
- /* At this stage in the game we don't want packets to be moving yet.
- The following probe calls should perform hardware setup
- needed to determine port counts. Receive must still be disabled */
switch (cvmx_helper_interface_get_mode(interface)) {
/* These types don't support ports to IPD/PKO */
case CVMX_HELPER_INTERFACE_MODE_DISABLED:
@@ -258,7 +253,7 @@ int cvmx_helper_interface_probe(int interface)
/* XAUI is a single high speed port */
case CVMX_HELPER_INTERFACE_MODE_XAUI:
interface_port_count[interface] =
- __cvmx_helper_xaui_probe(interface);
+ __cvmx_helper_xaui_enumerate(interface);
break;
/*
* RGMII/GMII/MII are all treated about the same. Most
@@ -267,7 +262,7 @@ int cvmx_helper_interface_probe(int interface)
case CVMX_HELPER_INTERFACE_MODE_RGMII:
case CVMX_HELPER_INTERFACE_MODE_GMII:
interface_port_count[interface] =
- __cvmx_helper_rgmii_probe(interface);
+ __cvmx_helper_rgmii_enumerate(interface);
break;
/*
* SPI4 can have 1-16 ports depending on the device at
@@ -275,7 +270,7 @@ int cvmx_helper_interface_probe(int interface)
*/
case CVMX_HELPER_INTERFACE_MODE_SPI:
interface_port_count[interface] =
- __cvmx_helper_spi_probe(interface);
+ __cvmx_helper_spi_enumerate(interface);
break;
/*
* SGMII can have 1-4 ports depending on how many are
@@ -284,12 +279,12 @@ int cvmx_helper_interface_probe(int interface)
case CVMX_HELPER_INTERFACE_MODE_SGMII:
case CVMX_HELPER_INTERFACE_MODE_PICMG:
interface_port_count[interface] =
- __cvmx_helper_sgmii_probe(interface);
+ __cvmx_helper_sgmii_enumerate(interface);
break;
/* PCI target Network Packet Interface */
case CVMX_HELPER_INTERFACE_MODE_NPI:
interface_port_count[interface] =
- __cvmx_helper_npi_probe(interface);
+ __cvmx_helper_npi_enumerate(interface);
break;
/*
* Special loopback only ports. These are not the same
@@ -297,7 +292,7 @@ int cvmx_helper_interface_probe(int interface)
*/
case CVMX_HELPER_INTERFACE_MODE_LOOP:
interface_port_count[interface] =
- __cvmx_helper_loop_probe(interface);
+ __cvmx_helper_loop_enumerate(interface);
break;
}
@@ -313,6 +308,74 @@ int cvmx_helper_interface_probe(int interface)
}
/**
+ * This function probes an interface to determine the actual
+ * number of hardware ports connected to it. It doesn't setup the
+ * ports or enable them. The main goal here is to set the global
+ * interface_port_count[interface] correctly. Hardware setup of the
+ * ports will be performed later.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Zero on success, negative on failure
+ */
+int cvmx_helper_interface_probe(int interface)
+{
+ cvmx_helper_interface_enumerate(interface);
+ /* At this stage in the game we don't want packets to be moving yet.
+ The following probe calls should perform hardware setup
+ needed to determine port counts. Receive must still be disabled */
+ switch (cvmx_helper_interface_get_mode(interface)) {
+ /* These types don't support ports to IPD/PKO */
+ case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+ case CVMX_HELPER_INTERFACE_MODE_PCIE:
+ break;
+ /* XAUI is a single high speed port */
+ case CVMX_HELPER_INTERFACE_MODE_XAUI:
+ __cvmx_helper_xaui_probe(interface);
+ break;
+ /*
+ * RGMII/GMII/MII are all treated about the same. Most
+ * functions refer to these ports as RGMII.
+ */
+ case CVMX_HELPER_INTERFACE_MODE_RGMII:
+ case CVMX_HELPER_INTERFACE_MODE_GMII:
+ __cvmx_helper_rgmii_probe(interface);
+ break;
+ /*
+ * SPI4 can have 1-16 ports depending on the device at
+ * the other end.
+ */
+ case CVMX_HELPER_INTERFACE_MODE_SPI:
+ __cvmx_helper_spi_probe(interface);
+ break;
+ /*
+ * SGMII can have 1-4 ports depending on how many are
+ * hooked up.
+ */
+ case CVMX_HELPER_INTERFACE_MODE_SGMII:
+ case CVMX_HELPER_INTERFACE_MODE_PICMG:
+ __cvmx_helper_sgmii_probe(interface);
+ break;
+ /* PCI target Network Packet Interface */
+ case CVMX_HELPER_INTERFACE_MODE_NPI:
+ __cvmx_helper_npi_probe(interface);
+ break;
+ /*
+ * Special loopback only ports. These are not the same
+ * as other ports in loopback mode.
+ */
+ case CVMX_HELPER_INTERFACE_MODE_LOOP:
+ __cvmx_helper_loop_probe(interface);
+ break;
+ }
+
+ /* Make sure all global variables propagate to other cores */
+ CVMX_SYNCWS;
+
+ return 0;
+}
+
+/**
* Setup the IPD/PIP for the ports on an interface. Packet
* classification and tagging are set for every port on the
* interface. The number of ports on the interface must already
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-loop.h b/arch/mips/include/asm/octeon/cvmx-helper-loop.h
index e646a6c..0a2488e 100644
--- a/arch/mips/include/asm/octeon/cvmx-helper-loop.h
+++ b/arch/mips/include/asm/octeon/cvmx-helper-loop.h
@@ -44,6 +44,7 @@
* Returns Number of ports on the interface. Zero to disable.
*/
extern int __cvmx_helper_loop_probe(int interface);
+static inline int __cvmx_helper_loop_enumerate(int interface) {return 4;}
/**
* Bringup and enable a LOOP interface. After this call packet
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-npi.h b/arch/mips/include/asm/octeon/cvmx-helper-npi.h
index 908e7b0..8df4c7f 100644
--- a/arch/mips/include/asm/octeon/cvmx-helper-npi.h
+++ b/arch/mips/include/asm/octeon/cvmx-helper-npi.h
@@ -45,6 +45,7 @@
* Returns Number of ports on the interface. Zero to disable.
*/
extern int __cvmx_helper_npi_probe(int interface);
+#define __cvmx_helper_npi_enumerate __cvmx_helper_npi_probe
/**
* Bringup and enable a NPI interface. After this call packet
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-rgmii.h b/arch/mips/include/asm/octeon/cvmx-helper-rgmii.h
index ea26526..78295ba 100644
--- a/arch/mips/include/asm/octeon/cvmx-helper-rgmii.h
+++ b/arch/mips/include/asm/octeon/cvmx-helper-rgmii.h
@@ -43,6 +43,7 @@
* Returns Number of RGMII/GMII/MII ports (0-4).
*/
extern int __cvmx_helper_rgmii_probe(int interface);
+#define __cvmx_helper_rgmii_enumerate __cvmx_helper_rgmii_probe
/**
* Put an RGMII interface in loopback mode. Internal packets sent
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-sgmii.h b/arch/mips/include/asm/octeon/cvmx-helper-sgmii.h
index 19b48d6..9a9b6c1 100644
--- a/arch/mips/include/asm/octeon/cvmx-helper-sgmii.h
+++ b/arch/mips/include/asm/octeon/cvmx-helper-sgmii.h
@@ -45,6 +45,7 @@
* Returns Number of ports on the interface. Zero to disable.
*/
extern int __cvmx_helper_sgmii_probe(int interface);
+extern int __cvmx_helper_sgmii_enumerate(int interface);
/**
* Bringup and enable a SGMII interface. After this call packet
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-spi.h b/arch/mips/include/asm/octeon/cvmx-helper-spi.h
index 69bac03..9f1c6b9 100644
--- a/arch/mips/include/asm/octeon/cvmx-helper-spi.h
+++ b/arch/mips/include/asm/octeon/cvmx-helper-spi.h
@@ -42,6 +42,7 @@
* Returns Number of ports on the interface. Zero to disable.
*/
extern int __cvmx_helper_spi_probe(int interface);
+extern int __cvmx_helper_spi_enumerate(int interface);
/**
* Bringup and enable a SPI interface. After this call packet I/O
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-xaui.h b/arch/mips/include/asm/octeon/cvmx-helper-xaui.h
index 4b4db2f..f6fbc4f 100644
--- a/arch/mips/include/asm/octeon/cvmx-helper-xaui.h
+++ b/arch/mips/include/asm/octeon/cvmx-helper-xaui.h
@@ -45,6 +45,7 @@
* Returns Number of ports on the interface. Zero to disable.
*/
extern int __cvmx_helper_xaui_probe(int interface);
+extern int __cvmx_helper_xaui_enumerate(int interface);
/**
* Bringup and enable a XAUI interface. After this call packet
diff --git a/arch/mips/include/asm/octeon/cvmx-helper.h b/arch/mips/include/asm/octeon/cvmx-helper.h
index 51916f3..3169cd7 100644
--- a/arch/mips/include/asm/octeon/cvmx-helper.h
+++ b/arch/mips/include/asm/octeon/cvmx-helper.h
@@ -207,6 +207,7 @@ extern int cvmx_helper_link_set(int ipd_port,
* Returns Zero on success, negative on failure
*/
extern int cvmx_helper_interface_probe(int interface);
+extern int cvmx_helper_interface_enumerate(int interface);
/**
* Configure a port for internal and/or external loopback. Internal loopback
--
1.7.2.3
More information about the devicetree-discuss
mailing list