[PATCH v3 2/3] ARM: mxc: use ARCH_NR_GPIOS to define gpio number

[Shawn Guo]

The patch removes MXC_GPIO_IRQS and instead uses ARCH_NR_GPIOS to
define gpio number.  This change is need when we change mxc gpio
driver to be device tree aware.  When migrating the driver to device
tree, pdev->id becomes unusable.  It requires driver get gpio range
from gpio core, which will dynamically allocates number from
ARCH_NR_GPIOS to 0.

As a bonus point, it removes lines of '#if' and make the code a
little bit cleaner.  The side effect is the waste of number.  But
this is not a point when we go single image.

Signed-off-by: Shawn Guo <shawn.guo at linaro.org>
Cc: Sascha Hauer <s.hauer at pengutronix.de>
Cc: Grant Likely <grant.likely at secretlab.ca>
---
 arch/arm/plat-mxc/include/mach/irqs.h |   21 +++------------------
 1 files changed, 3 insertions(+), 18 deletions(-)

diff --git a/arch/arm/plat-mxc/include/mach/irqs.h b/arch/arm/plat-mxc/include/mach/irqs.h
index 35c89bc..00e812b 100644
--- a/arch/arm/plat-mxc/include/mach/irqs.h
+++ b/arch/arm/plat-mxc/include/mach/irqs.h
@@ -11,6 +11,8 @@
 #ifndef __ASM_ARCH_MXC_IRQS_H__
 #define __ASM_ARCH_MXC_IRQS_H__
 
+#include <asm-generic/gpio.h>
+
 /*
  * SoCs with TZIC interrupt controller have 128 IRQs, those with AVIC have 64
  */
@@ -22,30 +24,13 @@
 
 #define MXC_GPIO_IRQ_START	MXC_INTERNAL_IRQS
 
-/* these are ordered by size to support multi-SoC kernels */
-#if defined CONFIG_SOC_IMX53
-#define MXC_GPIO_IRQS		(32 * 7)
-#elif defined CONFIG_ARCH_MX2
-#define MXC_GPIO_IRQS		(32 * 6)
-#elif defined CONFIG_SOC_IMX50
-#define MXC_GPIO_IRQS		(32 * 6)
-#elif defined CONFIG_ARCH_MX1
-#define MXC_GPIO_IRQS		(32 * 4)
-#elif defined CONFIG_ARCH_MX25
-#define MXC_GPIO_IRQS		(32 * 4)
-#elif defined CONFIG_SOC_IMX51
-#define MXC_GPIO_IRQS		(32 * 4)
-#elif defined CONFIG_ARCH_MX3
-#define MXC_GPIO_IRQS		(32 * 3)
-#endif
-
 /*
  * The next 16 interrupts are for board specific purposes.  Since
  * the kernel can only run on one machine at a time, we can re-use
  * these.  If you need more, increase MXC_BOARD_IRQS, but keep it
  * within sensible limits.
  */
-#define MXC_BOARD_IRQ_START	(MXC_INTERNAL_IRQS + MXC_GPIO_IRQS)
+#define MXC_BOARD_IRQ_START	(MXC_INTERNAL_IRQS + ARCH_NR_GPIOS)
 
 #ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
 #define MXC_BOARD_IRQS  80
-- 
1.7.4.1