[PATCH v2 3/3] mmc: sdhci-esdhc-imx: add device tree probe support

[Grant Likely]

On Wed, Jul 06, 2011 at 11:43:15PM +0800, Shawn Guo wrote:
> On Tue, Jul 05, 2011 at 11:54:34AM -0600, Grant Likely wrote:
> > On Tue, Jul 5, 2011 at 9:26 AM, Shawn Guo <shawn.guo at linaro.org> wrote:
> > > The patch adds device tree probe support for sdhci-esdhc-imx driver.
> > >
> > > Signed-off-by: Shawn Guo <shawn.guo at linaro.org>
> > > Cc: Wolfram Sang <w.sang at pengutronix.de>
> > > Cc: Chris Ball <cjb at laptop.org>
> > > Cc: Grant Likely <grant.likely at secretlab.ca>
> > > ---
> > >  .../devicetree/bindings/mmc/fsl-imx-esdhc.txt      |   40 ++++++++
> > >  drivers/mmc/host/sdhci-esdhc-imx.c                 |  102 +++++++++++++++++++-
> > >  2 files changed, 137 insertions(+), 5 deletions(-)
> > >  create mode 100644 Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> > >
> > > diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> > > new file mode 100644
> > > index 0000000..351d239
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> > > @@ -0,0 +1,40 @@
> > > +* Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX
> > > +
> > > +The Enhanced Secure Digital Host Controller on Freescale i.MX family
> > > +provides an interface for MMC, SD, and SDIO types of memory cards.
> > > +
> > > +Required properties:
> > > +- compatible : Should be "fsl,<chip>-esdhc"
> > > +- reg : Should contain eSDHC registers location and length
> > > +- interrupts : Should contain eSDHC interrupt
> > > +- cd-type : String, card detection (CD) method.  Supported values are:
> > > +    "none" : No CD
> > > +    "controller" : Uses eSDHC controller internal CD signal
> > > +    "gpio" : Uses GPIO pin for CD
> > > +    "permanent" : No CD because card is permanently wired to host
> > > +- wp-type : String, write protection (WP) method.  Supported values are:
> > > +    "none" : No WP
> > > +    "controller" : Uses eSDHC controller internal WP signal
> > > +    "gpio" : Uses GPIO pin for WP
> > > +- gpios : Should specify GPIOs in this order: CD GPIO, WP GPIO, if
> > > +  properties cd-type and wp-type are "gpio".
> > 
> > Again, be explicit in your gpios property names.  Create a different
> > property for each gpio: cd-gpios and wp-gpios.
> > 
> > As for wp-type and cd-type, I think you can drop them.  Default to
> > internal controller CD and WP pins.  Use gpio if cd-gpios or wp-gpios
> > is present, and define specific properties for the no-wp, no-cd and
> > fixed-card cases.  (can you tell that I'm not a fan of the "*-type"
> > binding for this driver?)  :-)
> > 
> I would let default be no CD/WP, and define properties for
> controller internal CD/WP and wired case, if you do not see a
> problem with it.

Okay.

g.