[PATCH] tty/serial: change of_serial to use new of_property_read_u32() api

[Rob Herring]

Grant,

On 06/30/2011 02:00 PM, Grant Likely wrote:
> Simplifies the code a bit and drops a few lines.
> 
> Signed-off-by: Grant Likely <grant.likely at secretlab.ca>
> ---
> 
> I've only actually build tested this, but this shows some of the cleanup
> achieved using the of_property_read_u32() API.  If this gets merged in the
> v3.1 merge window then it will need to go via the devicetree/next branch.
> 
> g.

You can't give yourself bonus points. ;)

> 
>  drivers/tty/serial/of_serial.c |   37 +++++++++++++++----------------------
>  1 files changed, 15 insertions(+), 22 deletions(-)
> 
> diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c
> index 36038ed..dbfbfda 100644
> --- a/drivers/tty/serial/of_serial.c
> +++ b/drivers/tty/serial/of_serial.c
> @@ -32,17 +32,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev,
>  {
>  	struct resource resource;
>  	struct device_node *np = ofdev->dev.of_node;
> -	const __be32 *clk, *spd;
> -	const __be32 *prop;
> -	int ret, prop_size;
> +	u32 clk, spd, prop;
> +	int ret;
>  
>  	memset(port, 0, sizeof *port);
> -	spd = of_get_property(np, "current-speed", NULL);
> -	clk = of_get_property(np, "clock-frequency", NULL);
> -	if (!clk) {
> +	if (of_property_read_u32(np, "clock-frequency", &clk)) {

s/clk/port->uartclk/

And below, then remove clk.

>  		dev_warn(&ofdev->dev, "no clock-frequency property set\n");
>  		return -ENODEV;
>  	}
> +	/* If current-speed was set, then try not to change it. */
> +	if (of_property_read_u32(np, "current-speed", &spd) == 0)
> +		port->custom_divisor = clk / (16 * spd);
>  
>  	ret = of_address_to_resource(np, 0, &resource);
>  	if (ret) {
> @@ -54,20 +54,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev,
>  	port->mapbase = resource.start;
>  
>  	/* Check for shifted address mapping */
> -	prop = of_get_property(np, "reg-offset", &prop_size);
> -	if (prop && (prop_size == sizeof(u32)))
> -		port->mapbase += be32_to_cpup(prop);
> +	if (of_property_read_u32(np, "reg-offset", &prop) == 0)
> +		port->mapbase += prop;
>  
>  	/* Check for registers offset within the devices address range */
> -	prop = of_get_property(np, "reg-shift", &prop_size);
> -	if (prop && (prop_size == sizeof(u32)))
> -		port->regshift = be32_to_cpup(prop);
> +	if (of_property_read_u32(np, "reg-shift", &prop) == 0)
> +		port->regshift = prop;

Can be further simplified:

of_property_read_u32(np, "reg-shift", &port->regshift);

Rob

>  
>  	port->irq = irq_of_parse_and_map(np, 0);
>  	port->iotype = UPIO_MEM;
> -	prop = of_get_property(np, "reg-io-width", &prop_size);
> -	if (prop && (prop_size == sizeof(u32))) {
> -		switch (be32_to_cpup(prop)) {
> +	if (of_property_read_u32(np, "reg-io-width", &prop) == 0) {
> +		switch (prop) {
>  		case 1:
>  			port->iotype = UPIO_MEM;
>  			break;
> @@ -75,21 +72,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev,
>  			port->iotype = UPIO_MEM32;
>  			break;
>  		default:
> -			dev_warn(&ofdev->dev,
> -				 "unsupported io width (%d bytes)\n",
> -				 be32_to_cpup(prop));
> +			dev_warn(&ofdev->dev, "unsupported reg-io-width (%d)\n",
> +				 prop);
>  			return -EINVAL;
>  		}
>  	}
>  
>  	port->type = type;
> -	port->uartclk = be32_to_cpup(clk);
> +	port->uartclk = clk;
>  	port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP
>  		| UPF_FIXED_PORT | UPF_FIXED_TYPE;
>  	port->dev = &ofdev->dev;
> -	/* If current-speed was set, then try not to change it. */
> -	if (spd)
> -		port->custom_divisor = be32_to_cpup(clk) / (16 * (be32_to_cpup(spd)));
>  
>  	return 0;
>  }
> 
> _______________________________________________
> devicetree-discuss mailing list
> devicetree-discuss at lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/devicetree-discuss