How to handle named resources with DT?

[Cousson, Benoit]

On 8/9/2011 10:55 PM, Grant Likely wrote:
> On Tue, Aug 09, 2011 at 07:47:20PM +0200, Cousson, Benoit wrote:
>> On 8/9/2011 7:23 PM, Grant Likely wrote:
>>> On Tue, Aug 9, 2011 at 10:57 AM, Cousson, Benoit<b-cousson at ti.com>   wrote:
>>>> Hi Manju,
>>>>
>>>> On 8/9/2011 6:29 PM, G, Manjunath Kondaiah wrote:
>>>>>
>>>>> Hi Benoit,
>>>>>
>>>>> On Tue, Aug 09, 2011 at 11:23:20AM +0200, Cousson, Benoit wrote:
>>>>>>
>>>>>> Hi Grant,
>>>>>>
>>>>>> Trying to bind hwmod informations with DT, I'm facing a little
>>>>>> limitation.
>>>>>> A bunch of drivers are using the platform_get_resource_byname, so
>>>>>> the name for the resource is needed.
>>>>>>
>>>>>> The name is used so far for IORESOURCE_MEM, IORESOURCE_IRQ and
>>>>>> IORESOURCE_DMA types of resources.
>>>>>
>>>>> IORESOURCE_MEM and IORESOURCE_IRQ's are fetched from dt blob and
>>>>> it will be part of pdev.
>>>>
>>>> Yes, but without the proper name in the resource structure. It will be then
>>>> impossible to use the platform_get_resource_byname function that is
>>>> currently used by a bunch of drivers.
>>>
>>> There is no analogous mechanism for _byname in the device tree.  The
>>> DT binding for a device must explicitly state what order the register
>>> ranges are in.  The driver will need to be adapted.
>>
>> That seems to be a small regression for my point of view. Relying on
>> the order is not super safe. This is not very readable either.
>> That's for that exact reason that we changed our drivers to use
>> platform_get_resource_byname. That's probably the reason why that
>> API is there as well.
>> For the same IP, the number of entries can vary depending of the SoC
>> revision.
>> By using the _byname, we can check if the resource is there or not
>> without having to care about the position.
>
> We've done it that way for a very long time with the device tree.  If
> you want to do something by name, then propose a binding that will
> make it work alongside the existing scheme.
>
>>
>>>>> For IORESOURCE_DMA, you can have property
>>>>> "dma-channel" in dtsi file and fetch dma-channel in driver probe
>>>>> through "of_property_read_u32()" api.
>>>>
>>>> That will not be enough to get the name. So maybe something like:
>>>>         dmas =<12>, "rx_req",<13>, "tx_req";
>>>> will be doable.
>>>> The issue is that the name is optional so managing the multiple entries
>>>> might be tricky.
>>>
>>> DMA channels will never show up in the resource structure anyway.
>>
>> Can you elaborate on that point? AFAIK, IORESOURCE_DMA is already
>> used today.
>
> IORESOURCE_DMA is a Linux construct, as is IORESOURCE_IRQ and
> IORESOURCE_MEM.  However, IRQ and MEM can be directly mapped from the
> common 'reg' and 'interrupts' bindings used by pretty much all device
> tree nodes.  Therefore common code can be written to translate MEM and
> IRQ that will always work.  There is no such common binding in place
> for DMA regions, so common setup code cannot do it transparently for
> the device driver.

OK, sure, I get your point now. I was thinking about a "potential" dma 
support from the core DT, since this is very similar to IRQ.

Otherwise, we can do it OMAP specific if nobody else care about that. 
But I still think it should be useful for other platforms.

Regards,
Benoit