[PATCH v3 2/2] powerpc/mpc5121: add initial support for PDM360NG board
Grant Likely
grant.likely at secretlab.ca
Sun Jul 25 17:42:23 EST 2010
On Fri, Jul 23, 2010 at 7:49 AM, Anatolij Gustschin <agust at denx.de> wrote:
> Adds IFM PDM360NG device tree, and platform code.
>
> Currently following is supported:
> - Spansion S29GL512P 256 MB NOR flash
> - ST Micro NAND 1 GiB flash
> - DIU, please use "fbcon=map:5 video=fslfb:800x480-32 at 60"
> at the kernel command line to enable PrimeView PM070WL3
> Display support.
> - FEC
> - I2C
> - RTC, EEPROM
> - MSCAN
> - PSC UART, please pass "console=tty0 console=ttyPSC5,115200"
> on the kernel command line.
> - SPI, ADS7845 Touchscreen
> - USB0/1 Host
> - USB0 OTG Host/Device
> - VIU, Overlay/Capture support
>
> Signed-off-by: Markus Fischer <markus.fischer.ec at ifm.com>
> Signed-off-by: Wolfgang Grandegger <wg at denx.de>
> Signed-off-by: Michael Weiss <michael.weiss at ifm.com>
> Signed-off-by: Detlev Zundel <dzu at denx.de>
> Signed-off-by: Anatolij Gustschin <agust at denx.de>
> Cc: devicetree-discuss at lists.ozlabs.org
> Cc: Grant Likely <grant.likely at secretlab.ca>
Hi Anatolij,
Finally got some time tonight to properly dig into this patch. Comments below.
> ---
> v3:
> - uncomment and correct .irq_flags field of touchscreen
> platform data struct as proposed extension to this
> data struct has been accepted and merged via input tree
> a short while ago
>
> v1 -> v2:
> - fix interrupt-parent property in nfc node
> - drop #address-cells in ipic node
> - remove device_type from ethernet-phy sub-node
> - remove device_type from ethernet node
> - add aliases node for eth0, needed for MAC address
> update by U-Boot
> - removed spaces around &ipic
>
> arch/powerpc/boot/dts/pdm360ng.dts | 432 ++++++++++++++++++++++++++++++++
> arch/powerpc/platforms/512x/Kconfig | 7 +
> arch/powerpc/platforms/512x/Makefile | 1 +
> arch/powerpc/platforms/512x/pdm360ng.c | 158 ++++++++++++
> 4 files changed, 598 insertions(+), 0 deletions(-)
> create mode 100644 arch/powerpc/boot/dts/pdm360ng.dts
> create mode 100644 arch/powerpc/platforms/512x/pdm360ng.c
>
> diff --git a/arch/powerpc/boot/dts/pdm360ng.dts b/arch/powerpc/boot/dts/pdm360ng.dts
> new file mode 100644
> index 0000000..7dc42e9
> --- /dev/null
> +++ b/arch/powerpc/boot/dts/pdm360ng.dts
> @@ -0,0 +1,432 @@
> +/*
> + * Device Tree Source for IFM PDM360NG.
> + *
> + * Copyright 2009 - 2010 DENX Software Engineering.
> + * Anatolij Gustschin <agust at denx.de>
> + *
> + * Based on MPC5121E ADS dts.
> + * Copyright 2008 Freescale Semiconductor Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or (at your
> + * option) any later version.
> + */
> +
> +/dts-v1/;
> +
> +/ {
> + model = "pdm360ng";
> + compatible = "ifm,pdm360ng";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + aliases {
> + ethernet0 = ð0;
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + PowerPC,5121 at 0 {
> + device_type = "cpu";
> + reg = <0>;
> + d-cache-line-size = <0x20>; // 32 bytes
> + i-cache-line-size = <0x20>; // 32 bytes
> + d-cache-size = <0x8000>; // L1, 32K
> + i-cache-size = <0x8000>; // L1, 32K
> + timebase-frequency = <49500000>;// 49.5 MHz (csb/4)
> + bus-frequency = <198000000>; // 198 MHz csb bus
> + clock-frequency = <396000000>; // 396 MHz ppc core
> + };
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x20000000>; // 512MB at 0
> + };
> +
> + nfc at 40000000 {
> + compatible = "fsl,mpc5121-nfc";
> + reg = <0x40000000 0x100000>;
> + interrupts = <0x6 0x8>;
> + interrupt-parent = <&ipic>;
This device tree can be less verbose if you remove the
interrupt-parent property from all the nodes, and have a single
interrupt-parent = <&ipic>; in the root node. Nodes inherit the
interrupt-parent from their (grand-)parents.
> + #address-cells = <0x1>;
> + #size-cells = <0x1>;
> + bank-width = <0x1>;
> + chips = <0x1>;
> +
> + partition at 0 {
> + label = "nand0";
> + reg = <0x0 0x40000000>;
> + };
> + };
> +
> + sram at 50000000 {
> + compatible = "fsl,mpc5121-sram";
> + reg = <0x50000000 0x20000>; // 128K at 0x50000000
> + };
> +
> + localbus at 80000020 {
> + compatible = "fsl,mpc5121-localbus";
> + #address-cells = <2>;
> + #size-cells = <1>;
> + reg = <0x80000020 0x40>;
> +
> + ranges = <0x0 0x0 0xf0000000 0x10000000 /* Flash */
> + 0x2 0x0 0x50040000 0x00020000>; /* CS2: MRAM */
> +
> + flash at 0,0 {
> + compatible = "amd,s29gl01gp", "cfi-flash";
> + reg = <0 0x00000000 0x08000000
> + 0 0x08000000 0x08000000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + bank-width = <4>;
> + device-width = <2>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x00000000 0x00080000>;
> + read-only;
> + };
> + partition at 80000 {
> + label = "environment";
> + reg = <0x00080000 0x00080000>;
> + read-only;
> + };
> + partition at 100000 {
> + label = "splash-image";
> + reg = <0x00100000 0x00080000>;
> + read-only;
> + };
> + partition at 180000 {
> + label = "device-tree";
> + reg = <0x00180000 0x00040000>;
> + };
> + partition at 1c0000 {
> + label = "kernel";
> + reg = <0x001c0000 0x00500000>;
> + };
> + partition at 6c0000 {
> + label = "filesystem";
> + reg = <0x006c0000 0x07940000>;
> + };
> + };
> +
> + mram0 at 2,0 {
> + compatible = "mtd-ram";
> + reg = <2 0x00000 0x10000>;
> + bank-width = <2>;
> + };
> +
> + mram1 at 2,10000 {
> + compatible = "mtd-ram";
> + reg = <2 0x010000 0x10000>;
> + bank-width = <2>;
> + };
> + };
> +
> + soc at 80000000 {
> + compatible = "fsl,mpc5121-immr";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #interrupt-cells = <2>;
> + ranges = <0x0 0x80000000 0x400000>;
> + reg = <0x80000000 0x400000>;
> + bus-frequency = <66000000>; // 66 MHz ips bus
> +
> + // IPIC
> + // interrupts cell = <intr #, sense>
> + // sense values match linux IORESOURCE_IRQ_* defines:
> + // sense == 8: Level, low assertion
> + // sense == 2: Edge, high-to-low change
> + //
> + ipic: interrupt-controller at c00 {
> + compatible = "fsl,mpc5121-ipic", "fsl,ipic";
> + interrupt-controller;
> + #address-cells = <0>;
> + #interrupt-cells = <2>;
> + reg = <0xc00 0x100>;
> + };
> +
> + rtc at a00 { // Real time clock
> + compatible = "fsl,mpc5121-rtc";
> + reg = <0xa00 0x100>;
> + interrupts = <79 0x8 80 0x8>;
> + interrupt-parent = <&ipic>;
> + };
> +
> + reset at e00 { // Reset module
> + compatible = "fsl,mpc5121-reset";
> + reg = <0xe00 0x100>;
> + };
> +
> + clock at f00 { // Clock control
> + compatible = "fsl,mpc5121-clock";
> + reg = <0xf00 0x100>;
> + };
> +
> + pmc at 1000{ //Power Management Controller
> + compatible = "fsl,mpc5121-pmc";
> + reg = <0x1000 0x100>;
> + interrupts = <83 0x2>;
> + interrupt-parent = <&ipic>;
> + };
> +
> + gpio at 1100 {
> + compatible = "fsl,mpc5121-gpio";
> + reg = <0x1100 0x100>;
> + interrupts = <78 0x8>;
> + interrupt-parent = <&ipic>;
> + };
> +
> + can at 1300 {
> + compatible = "fsl,mpc5121-mscan";
> + interrupts = <12 0x8>;
> + interrupt-parent = <&ipic>;
> + reg = <0x1300 0x80>;
> + };
> +
> + can at 1380 {
> + compatible = "fsl,mpc5121-mscan";
> + interrupts = <13 0x8>;
> + interrupt-parent = <&ipic>;
> + reg = <0x1380 0x80>;
> + };
> +
> + i2c at 1700 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,mpc5121-i2c";
> + reg = <0x1700 0x20>;
> + interrupts = <0x9 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,preserve-clocking;
> +
> + eeprom at 50 {
> + compatible = "at,24c01";
> + reg = <0x50>;
> + };
> +
> + rtc at 68 {
> + compatible = "stm,m41t00";
> + reg = <0x68>;
> + };
> + };
> +
> + i2c at 1740 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,mpc5121-i2c";
> + reg = <0x1740 0x20>;
> + interrupts = <0xb 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,preserve-clocking;
> + };
> +
> + i2ccontrol at 1760 {
> + compatible = "fsl,mpc5121-i2c-ctrl";
> + reg = <0x1760 0x8>;
> + };
> +
> + axe at 2000 {
> + compatible = "fsl,mpc5121-axe";
> + reg = <0x2000 0x100>;
> + interrupts = <42 0x8>;
> + interrupt-parent = <&ipic>;
> + };
> +
> + display at 2100 {
> + compatible = "fsl,mpc5121-diu";
> + reg = <0x2100 0x100>;
> + interrupts = <64 0x8>;
> + interrupt-parent = <&ipic>;
> + };
> +
> + can at 2300 {
> + compatible = "fsl,mpc5121-mscan";
> + interrupts = <90 0x8>;
> + interrupt-parent = <&ipic>;
> + reg = <0x2300 0x80>;
> + };
> +
> + can at 2380 {
> + compatible = "fsl,mpc5121-mscan";
> + interrupts = <91 0x8>;
> + interrupt-parent = <&ipic>;
> + reg = <0x2380 0x80>;
> + };
> +
> + viu at 2400 {
> + compatible = "fsl,mpc5121-viu";
> + reg = <0x2400 0x400>;
> + interrupts = <67 0x8>;
> + interrupt-parent = <&ipic>;
> + };
> +
> + mdio at 2800 {
> + compatible = "fsl,mpc5121-fec-mdio";
> + reg = <0x2800 0x200>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy: ethernet-phy at 0 {
> + reg = <0x1f>;
For completeness, phy should have a compatible property.
> + };
> + };
> +
> + eth0: ethernet at 2800 {
> + compatible = "fsl,mpc5121-fec";
> + reg = <0x2800 0x200>;
> + local-mac-address = [ 00 00 00 00 00 00 ];
> + interrupts = <4 0x8>;
> + interrupt-parent = <&ipic>;
> + phy-handle = < &phy >;
> + };
> +
> + // USB1 using external ULPI PHY
> + usb at 3000 {
> + compatible = "fsl,mpc5121-usb2-dr";
> + reg = <0x3000 0x600>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupt-parent = <&ipic>;
> + interrupts = <43 0x8>;
> + dr_mode = "host";
> + phy_type = "ulpi";
> + };
> +
> + // USB0 using internal UTMI PHY
> + usb at 4000 {
> + compatible = "fsl,mpc5121-usb2-dr";
> + reg = <0x4000 0x600>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupt-parent = <&ipic>;
> + interrupts = <44 0x8>;
> + dr_mode = "otg";
> + phy_type = "utmi_wide";
> + fsl,invert-pwr-fault;
> + };
> +
> + // IO control
> + ioctl at a000 {
> + compatible = "fsl,mpc5121-ioctl";
> + reg = <0xA000 0x1000>;
> + };
> +
> + // 512x PSCs are not 52xx PSCs compatible
> + serial at 11000 {
> + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
> + cell-index = <0>;
> + reg = <0x11000 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,rx-fifo-size = <16>;
> + fsl,tx-fifo-size = <16>;
> + };
> +
> + serial at 11100 {
> + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
> + cell-index = <1>;
> + reg = <0x11100 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,rx-fifo-size = <16>;
> + fsl,tx-fifo-size = <16>;
> + };
> +
> + serial at 11200 {
> + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
> + cell-index = <2>;
> + reg = <0x11200 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,rx-fifo-size = <16>;
> + fsl,tx-fifo-size = <16>;
> + };
> +
> + serial at 11300 {
> + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
> + cell-index = <3>;
> + reg = <0x11300 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,rx-fifo-size = <16>;
> + fsl,tx-fifo-size = <16>;
> + };
> +
> + serial at 11400 {
> + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
> + cell-index = <4>;
> + reg = <0x11400 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,rx-fifo-size = <16>;
> + fsl,tx-fifo-size = <16>;
> + };
> +
> + serial at 11600 {
> + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
> + cell-index = <6>;
> + reg = <0x11600 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,rx-fifo-size = <16>;
> + fsl,tx-fifo-size = <16>;
> + };
> +
> + serial at 11800 {
> + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
> + cell-index = <8>;
> + reg = <0x11800 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,rx-fifo-size = <16>;
> + fsl,tx-fifo-size = <16>;
> + };
> +
> + serial at 11B00 {
> + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
> + cell-index = <11>;
> + reg = <0x11B00 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,rx-fifo-size = <16>;
> + fsl,tx-fifo-size = <16>;
> + };
> +
> + pscfifo at 11f00 {
> + compatible = "fsl,mpc5121-psc-fifo";
> + reg = <0x11f00 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + };
> +
> + spi at 11900 {
> + compatible = "fsl,mpc5121-psc-spi", "fsl,mpc5121-psc";
> + cell-index = <9>;
Try to drop the cell-index properties. They are almost always misused.
> + reg = <0x11900 0x100>;
> + interrupts = <40 0x8>;
> + interrupt-parent = <&ipic>;
> + fsl,rx-fifo-size = <16>;
> + fsl,tx-fifo-size = <16>;
> +
> + // 7845 touch screen controller
> + ts at 0 {
> + compatible = "ti,ads7845";
> + interrupt-parent = <&ipic>;
> + // pen irq is GPIO25
> + interrupts = <78 0x8>;
> + };
> + };
> +
> + dma at 14000 {
> + compatible = "fsl,mpc5121-dma";
> + reg = <0x14000 0x1800>;
> + interrupts = <65 0x8>;
> + interrupt-parent = <&ipic>;
> + };
> + };
> +};
> diff --git a/arch/powerpc/platforms/512x/Kconfig b/arch/powerpc/platforms/512x/Kconfig
> index e9dca28..27b0651 100644
> --- a/arch/powerpc/platforms/512x/Kconfig
> +++ b/arch/powerpc/platforms/512x/Kconfig
> @@ -25,3 +25,10 @@ config MPC5121_GENERIC
>
> Compatible boards include: Protonic LVT base boards (ZANMCU
> and VICVT2).
> +
> +config PDM360NG
> + bool "ifm PDM360NG board"
> + depends on PPC_MPC512x
> + select DEFAULT_UIMAGE
> + help
> + This option enables support for the PDM360NG board.
> diff --git a/arch/powerpc/platforms/512x/Makefile b/arch/powerpc/platforms/512x/Makefile
> index 90be2f5..4efc1c4 100644
> --- a/arch/powerpc/platforms/512x/Makefile
> +++ b/arch/powerpc/platforms/512x/Makefile
> @@ -4,3 +4,4 @@
> obj-y += clock.o mpc512x_shared.o
> obj-$(CONFIG_MPC5121_ADS) += mpc5121_ads.o mpc5121_ads_cpld.o
> obj-$(CONFIG_MPC5121_GENERIC) += mpc5121_generic.o
> +obj-$(CONFIG_PDM360NG) += pdm360ng.o
> diff --git a/arch/powerpc/platforms/512x/pdm360ng.c b/arch/powerpc/platforms/512x/pdm360ng.c
> new file mode 100644
> index 0000000..01e6023
> --- /dev/null
> +++ b/arch/powerpc/platforms/512x/pdm360ng.c
> @@ -0,0 +1,158 @@
> +/*
> + * Copyright (C) 2010 DENX Software Engineering
> + *
> + * Anatolij Gustschin, <agust at denx.de>
> + *
> + * PDM360NG board setup
> + *
> + * This is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/io.h>
> +#include <linux/of_platform.h>
> +
> +#include <asm/machdep.h>
> +#include <asm/ipic.h>
> +#include <asm/prom.h>
> +
> +#include "mpc512x.h"
> +
> +#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
> + defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
> +#include <linux/fsl_devices.h>
> +#include <linux/interrupt.h>
> +#include <linux/spi/ads7846.h>
> +#include <linux/spi/spi.h>
> +
> +static void *pdm360ng_gpio_base;
> +
> +static int pdm360ng_get_pendown_state(void)
> +{
> + u32 reg;
> +
> + reg = in_be32((u32 *)(pdm360ng_gpio_base + 0xc));
> + if (reg & 0x40)
> + setbits32((u32 *)(pdm360ng_gpio_base + 0xc), 0x40);
> +
> + reg = in_be32((u32 *)(pdm360ng_gpio_base + 0x8));
(u32*) casts are unnecessary and can be removed.
> +
> + /* return 1 if pen is down */
> + return reg & 0x40 ? 0 : 1;
return reg & 0x40 == 0;
> +}
> +
> +static struct ads7846_platform_data pdm360ng_ads7846_pdata __initdata = {
> + .model = 7845,
> + .get_pendown_state = pdm360ng_get_pendown_state,
> + .irq_flags = IRQF_TRIGGER_LOW,
> +};
> +
> +static int __init pdm360ng_penirq_init(void)
> +{
> + struct device_node *np;
> + struct resource r;
> +
> + np = of_find_compatible_node(NULL, NULL, "fsl,mpc5121-gpio");
> + if (!np) {
> + pr_err("%s: Can't find 'mpc5121-gpio' node\n", __func__);
> + return -1;
> + }
return -ENODEV;
> +
> + if (of_address_to_resource(np, 0, &r)) {
> + pr_err("%s: Invalid gpio address.\n", __func__);
> + of_node_put(np);
> + return -1;
ditto
> + }
> + of_node_put(np);
> +
> + pdm360ng_gpio_base = ioremap(r.start, resource_size(&r));
Or you could have simply used of_iomap() to eliminate some code.
> + if (!pdm360ng_gpio_base) {
> + pr_err("%s: Can't map gpio regs.\n", __func__);
> + return -1;
ditto
> + }
> + out_be32((u32 *)pdm360ng_gpio_base + 0xc, 0xffffffff);
> + setbits32((u32 *)(pdm360ng_gpio_base + 0x18), 0x2000);
> + setbits32((u32 *)(pdm360ng_gpio_base + 0x10), 0x40);
> +
> + return 0;
> +}
> +
> +static int __init pdm360ng_touchscreen_init(void)
> +{
> + struct device_node *np;
> + struct of_device *of_dev;
> + struct spi_board_info info;
> + const u32 *prop;
> + int bus_num = -1;
> + int len;
> +
> + np = of_find_compatible_node(NULL, NULL, "ti,ads7845");
> + if (!np)
> + return -ENODEV;
> +
> + memset(&info, 0, sizeof(info));
> + info.irq = irq_of_parse_and_map(np, 0);
> + if (info.irq == NO_IRQ)
> + return -ENODEV;
> +
> + info.platform_data = &pdm360ng_ads7846_pdata;
> + if (strlcpy(info.modalias, "ads7846",
> + SPI_NAME_SIZE) >= SPI_NAME_SIZE)
> + return -ENOMEM;
> +
> + np = of_get_next_parent(np);
> + if (!np)
> + return -ENODEV;
> +
> + prop = of_get_property(np, "cell-index", &len);
> + if (prop && len == 4)
> + bus_num = *prop;
Blech. Don't use cell-index for bus enumeration. In fact, none of
this should be necessary at all (see below).
> +
> + if (bus_num < 0 || bus_num > 11)
> + return -ENODEV;
> +
> + info.bus_num = bus_num;
> +
> + of_dev = of_find_device_by_node(np);
> + of_node_put(np);
> + if (of_dev) {
> + struct fsl_spi_platform_data *pdata;
> +
> + pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
> + if (pdata) {
> + pdata->bus_num = bus_num;
> + pdata->max_chipselect = 1;
> + of_dev->dev.platform_data = pdata;
> + }
> + }
> +
> + if (pdm360ng_penirq_init())
> + return -ENODEV;
> +
> + return spi_register_board_info(&info, 1);
This ends up being a lot of code simply to attach a pdata structure to
an spi device. I've been thinking about this problem, and I think
there is a better way. Instead, use a bus notifier attached to the
SPI bus to wait for the spi_device to get registered, but before it
gets bound to a driver. Then you can attach the pdata structure very
simply. Something like this I think (completely untested, or even
compiled. Details are left as an exercise to the developer):
static int pdm360ng_touchscreen_notifier_call(struct notifier_block *nb,
unsigned long event, void *__dev)
{
struct device *dev = __dev;
if ((event == BUS_NOTIFIY_ADD_DEVICE) && (dev->of_node == [FOO]))
dev->platform_data = [BAR];
}
static struct notifier_block pdm360ng_touchscreen_nb = {
notifier_call = pdm360ng_touchscreen_notifier_call;
};
static int __init pdm360ng_touchscreen_init(void)
{
bus_register_notifier(&spi_bus_type, pdm360ng_touchscreen_nb);
}
> +}
> +machine_device_initcall(pdm360ng, pdm360ng_touchscreen_init);
This code is *in the same file* as the board setup file. Don't use an
initcall. Call it from the init callback instead.
> +#endif
> +
> +static int __init pdm360ng_probe(void)
> +{
> + unsigned long root = of_get_flat_dt_root();
> +
> + return of_flat_dt_is_compatible(root, "ifm,pdm360ng");
> +}
> +
> +define_machine(pdm360ng) {
> + .name = "PDM360NG",
> + .probe = pdm360ng_probe,
> + .setup_arch = mpc512x_setup_diu,
> + .init = mpc512x_init,
> + .init_early = mpc512x_init_diu,
> + .init_IRQ = mpc512x_init_IRQ,
> + .get_irq = ipic_get_irq,
> + .calibrate_decr = generic_calibrate_decr,
> + .restart = mpc512x_restart,
> +};
> --
> 1.7.0.4
>
>
--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
More information about the devicetree-discuss
mailing list