<div>Good evening,
</div><div><br></div><div>I recently tested the latest 3.10-rc release (rc4) on my powerpc based routerboard which is currently running very stable on a 3.9 release.</div><div>During boot I immediately got a kernel panic.</div><div><br></div><div>I was able to get a log of the trace with the serial console.</div><div><br></div><div><div>[ 0.039522] PCI: Probing PCI hardware</div><div>[ 0.043159] PCI: Memory resource 0 not set for host bridge /pci@e0008500 (domain 0)</div><div>[ 0.050778] PCI: Memory resource 0 not set for host bridge /pci@e0008500 (domain 0)</div><div>[ 0.058855] PCI host bridge to bus 0000:00</div><div>[ 0.062938] pci_bus 0000:00: root bus resource [io 0x0000-0xffffff]</div><div>[ 0.069255] pci_bus 0000:00: root bus resource [mem 0x80000000-0x9fffffff]</div><div>[ 0.076131] pci_bus 0000:00: root bus resource [bus 00-ff]</div><div>[ 0.081639] Unable to handle kernel paging request for data at address 0x00000f14</div><div>[ 0.089068] Faulting instruction address: 0xc0014d40</div><div>[ 0.094031] Oops: Kernel access of bad area, sig: 11 [#1]</div><div>[ 0.099420] MikroTik RouterBOARD 600 series</div><div>[ 0.103597] Modules linked in:</div><div>[ 0.106651] CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc1+ #15</div><div>[ 0.112910] task: c782e000 ti: c7834000 task.ti: c7834000</div><div>[ 0.118303] NIP: c0014d40 LR: c0014dd8 CTR: c0014e10</div><div>[ 0.123262] REGS: c7835b40 TRAP: 0300 Not tainted (3.10.0-rc1+)</div><div>[ 0.129435] MSR: 00001032 <ME,IR,DR,RI> CR: 22000084 XER: 20000000</div><div>[ 0.135788] DAR: 00000f14, DSISR: 20000000</div><div>[ 0.139875]</div><div>GPR00: c0014e40 c7835bf0 c782e000 c0417000 00000000 00000000 00000004 00000000</div><div>GPR08: 00000000 00000000 00000000 00000037 22000084 00000000 c0003e90 00000000</div><div>GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000045</div><div>GPR24: c0400000 c03f0000 c036134c c782de00 00000000 0000ea60 c782de00 c0417000</div><div>[ 0.169567] NIP [c0014d40] fsl_pcie_check_link.part.4+0x8/0x2c</div><div>[ 0.175380] LR [c0014dd8] fsl_pcie_check_link+0x74/0xac</div><div>[ 0.180591] Call Trace:</div><div>[ 0.183033] [c7835bf0] [00000025] 0x25 (unreliable)</div><div>[ 0.187909] [c7835d80] [c0014e40] fsl_indirect_read_config+0x30/0x8c</div><div>[ 0.194270] [c7835da0] [c019c108] pci_bus_read_config_dword+0x60/0x80</div><div>[ 0.200703] [c7835dc0] [c019df3c] pci_bus_read_dev_vendor_id+0x34/0x108</div><div>[ 0.207321] [c7835df0] [c022d394] pci_scan_single_device+0x58/0xc8</div><div>[ 0.213488] [c7835e20] [c019f068] pci_scan_slot+0x54/0x110</div><div>[ 0.218969] [c7835e40] [c019fc40] pci_scan_child_bus+0x28/0xdc</div><div>[ 0.224811] [c7835e60] [c0010aa4] pcibios_scan_phb+0x19c/0x210</div><div>[ 0.230640] [c7835e90] [c03b4658] pcibios_init+0x7c/0x114</div><div>[ 0.236025] [c7835ec0] [c00039a4] do_one_initcall+0x150/0x1a4</div><div>[ 0.241763] [c7835ef0] [c03b1888] kernel_init_freeable+0x114/0x1bc</div><div>[ 0.247938] [c7835f30] [c0003ea8] kernel_init+0x18/0x110</div><div>[ 0.253247] [c7835f40] [c000e098] ret_from_kernel_thread+0x64/0x6c</div><div>[ 0.259417] --- Exception: 0 at (null)</div><div>[ 0.259417] LR = (null)</div><div>[ 0.266287] Instruction dump:</div><div>[ 0.269246] 3d400006 614a0400 915f0028 3d40c040 912afc88 80010024 83e1001c 38210020</div><div>[ 0.276988] 7c0803a6 4e800020 812300ec 7c0004ac <80690f14> 0c030000 4c00012c 5463f6be</div><div>[ 0.284945] ---[ end trace 074b946a523243d5 ]---</div></div><div><br></div><div>Compare this to booting with 3.9</div><div><br></div><div><div>[ 0.039088] PCI: Probing PCI hardware</div><div>[ 0.043151] PCI host bridge to bus 0000:00</div><div>[ 0.047232] pci_bus 0000:00: root bus resource [io 0x0000-0xffffff]</div><div>[ 0.053546] pci_bus 0000:00: root bus resource [mem 0x80000000-0x9fffffff]</div><div>[ 0.060419] pci_bus 0000:00: root bus resource [bus 00-ff]</div><div>[ 0.068080] pci 0000:00:0d.0: BAR 0: assigned [mem 0x80000000-0x8000ffff]</div><div>[ 0.074854] pci 0000:00:0b.0: BAR 0: assigned [io 0x1000-0x10ff]</div><div>[ 0.080908] pci 0000:00:0b.0: BAR 1: assigned [mem 0x80010000-0x800100ff]</div><div>[ 0.103986] bio: create slab <bio-0> at 0</div><div>[ 0.108589] Freescale Elo / Elo Plus DMA driver</div><div>[ 0.115166] SCSI subsystem initialized</div></div><div><br></div><div>Especially I do not understand why this message shows up now</div><div> </div><div>PCI: Memory resource 0 not set for host bridge</div><div><br></div><div>Does someone have an idea what's happening here?</div><div>I tested this also on rc1 and got the same panic there.</div><div>Please CC me on any replies since I am not subscribed to the list.</div><div><br></div><div>Thank you very much in advance,</div><div>Michael Guntsche</div><div> </div>
<div></div>