--------------------------------------------------------------- Boot linux 2.6.26 ---------------------------------------------------------------- Using MPC834x ITX machine description Linux version 2.6.26 (olivier@olivier-desktop) (gcc version 4.2.1 (Sourcery G++ Lite 4.2-82)) #35 Tue Jul 29 16:55:34 CEST 2008 Found initrd at 0xcf829000:0xcff74b4a Found MPC83xx PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0 PCI host bridge /pci@e0008500 (primary) ranges: MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 Prefetch MEM 0x0000000090000000..0x000000009fffffff -> 0x0000000090000000 IO 0x00000000e2000000..0x00000000e2ffffff -> 0x0000000000000000 Found MPC83xx PCI host bridge at 0x00000000e0008600. Firmware bus number: 0->0 PCI host bridge /pci@e0008600 ranges: MEM 0x00000000a0000000..0x00000000afffffff -> 0x00000000a0000000 Prefetch MEM 0x00000000b0000000..0x00000000bfffffff -> 0x00000000b0000000 IO 0x00000000e3000000..0x00000000e3ffffff -> 0x0000000000000000 Zone PFN ranges: DMA 0 -> 65536 Normal 65536 -> 65536 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 65536 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: root=/dev/ram ramdisk_size=80000 rw ip=192.168.0.20:192.168.0.42:192.168.1.254:255.255.255.0:PowerQUICC:eth0:off console=ttyS1,115200 md=0,/dev/sda,/dev/sdb,/dev/sdc,/dev/sdd md: Will configure md0 (super-block) from /dev/sda,/dev/sdb,/dev/sdc,/dev/sdd, below. IPIC (128 IRQ sources) at fbffc700 PID hash table entries: 1024 (order: 10, 4096 bytes) clocksource: timebase mult[3c00001] shift[22] registered Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 248440k/262144k available (3356k kernel code, 13384k reserved, 116k data, 100k bss, 168k init) SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Mount-cache hash table entries: 512 net_namespace: 192 bytes xor: measuring software checksum speed 8regs : 405.000 MB/sec 8regs_prefetch: 385.000 MB/sec 32regs : 485.000 MB/sec 32regs_prefetch: 471.000 MB/sec xor: using function: 32regs (485.000 MB/sec) NET: Registered protocol family 16 PCI: Probing PCI hardware SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 7470k freed msgmni has been set to 500 async_tx: api initialized (async) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 18) is a 16550A serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 19) is a 16550A console [ttyS1] enabled brd: module loaded loop: module loaded eth0: Gianfar Ethernet Controller Version 1.2, 08:00:3e:03:01:11 eth0: Running with NAPI enabled eth0: 256/256 RX/TX BD ring size eth1: Gianfar Ethernet Controller Version 1.2, 08:00:3e:03:01:12 eth1: Running with NAPI enabled eth1: 256/256 RX/TX BD ring size Fixed MDIO Bus: probed Driver 'sd' needs updating - please use bus_type methods sata_sil 0000:00:10.0: enabling device (0000 -> 0003) sata_sil 0000:00:10.0: cache line size not set. Driver may not function sata_sil 0000:00:10.0: Applying R_ERR on DMA activate FIS errata fix scsi0 : sata_sil scsi1 : sata_sil scsi2 : sata_sil scsi3 : sata_sil ata1: SATA max UDMA/100 mmio m1024@0x90000000 tf 0x90000080 irq 22 ata2: SATA max UDMA/100 mmio m1024@0x90000000 tf 0x900000c0 irq 22 ata3: SATA max UDMA/100 mmio m1024@0x90000000 tf 0x90000280 irq 22 ata4: SATA max UDMA/100 mmio m1024@0x90000000 tf 0x900002c0 irq 22 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-7: Maxtor 6V250F0, VA111900, max UDMA/133 ata1.00: 490234752 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata2.00: ATA-7: Maxtor 6V250F0, VA111900, max UDMA/133 ata2.00: 490234752 sectors, multi 0: LBA48 NCQ (depth 0/32) ata2.00: configured for UDMA/100 ata3: SATA link down (SStatus 0 SControl 310) ata4: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Maxtor 6V250F0 VA11 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda:<3>ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x20 (host bus error) ata1.00: status: { DRDY } ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata1.00: revalidation failed (errno=-5) ata1: failed to recover some devices, retrying in 5 secs ata1: hard resetting link ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: configured for UDMA/100 ata1: EH complete ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x20 (host bus error) ata1.00: status: { DRDY } ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata1.00: revalidation failed (errno=-5) ata1: failed to recover some devices, retrying in 5 secs ata1: hard resetting link ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: configured for UDMA/100 ata1: EH complete ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x20 (host bus error) ata1.00: status: { DRDY } !!!!! The boot process hangs here !!!! --------------------------------------------------------------- Boot linux 2.6.13 ---------------------------------------------------------------- Linux version 2.6.13.4 (root@LINUX-MICETEK) (gcc version 3.4.3) #1 Mon Mar 10 13:39:07 CST 2008 PCI2 confirm: isa_io_base = 0xfc000000 Configure PCI2 controller isa_io_base = 0xfc000000 hose2->io_base_virt = 0xfd000000 Built 1 zonelists Kernel command line: root=/dev/ram ramdisk_size=80000 rw ip=192.168.0.20:192.168.0.42:192.168.1.254:255.255.255.0:PowerQUICC:eth0:off console=ttyS1,115200 md=0,/dev/sda,/dev/sdb,/dev/sdc,/dev/sdd md: Will configure md0 (super-block) from /dev/sda,/dev/sdb,/dev/sdc,/dev/sdd, below. IPIC (128 IRQ sources, 8 External IRQs) at fe000700 PID hash table entries: 2048 (order: 11, 32768 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 254208k available (2400k kernel code, 876k data, 112k init, 0k highmem) Mount-cache hash table entries: 512 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 1864k freed NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Cannot allocate resource region 0 of device 0000:00:00.0 PCI: Cannot allocate resource region 2 of device 0000:00:00.0 PCI: Cannot allocate resource region 0 of device 0001:01:00.0 PCI: Cannot allocate resource region 2 of device 0001:01:00.0 PCI: Failed to allocate mem resource #2:80000000@0 for 0000:00:00.0 PCI: Failed to allocate mem resource #2:80000000@0 for 0001:01:00.0 SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub NTFS driver 2.1.23 [Flags: R/W DEBUG]. Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A ttyS1 at MMIO 0xe0004600 (irq = 10) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 80000K size 1024 blocksize loop: loaded (max 8 devices) Intel(R) PRO/1000 Network Driver - version 6.0.60-k2-NAPI Copyright (c) 1999-2005 Intel Corporation. eth0: Gianfar Ethernet Controller Version 1.4, 08:00:3e:03:01:11 eth0: MTU = 1500 (frame size=1514,truesize=1780) eth0: Running with NAPI enabled eth0: 64/64 RX/TX BD ring size eth0: Socket buffer recycling mode enabled eth1: Gianfar Ethernet Controller Version 1.4, 08:00:3e:03:01:12 eth1: MTU = 1500 (frame size=1514,truesize=1780) eth1: Running with NAPI enabled eth1: 64/64 RX/TX BD ring size eth1: Socket buffer recycling mode enabled SKB Handler initialized(max=64) sata_sil(0000:00:10.0): cache line size not set. Driver may not function ata1: SATA max UDMA/100 cmd 0xD1000C80 ctl 0xD1000C8A bmdma 0xD1000C00 irq 22 ata2: SATA max UDMA/100 cmd 0xD1000CC0 ctl 0xD1000CCA bmdma 0xD1000C08 irq 22 ata3: SATA max UDMA/100 cmd 0xD1000E80 ctl 0xD1000E8A bmdma 0xD1000E00 irq 22 ata4: SATA max UDMA/100 cmd 0xD1000EC0 ctl 0xD1000ECA bmdma 0xD1000E08 irq 22 ata1: dev 0 ATA, max UDMA/133, 490234752 sectors: lba48 ata1: dev 0 configured for UDMA/100 scsi0 : sata_sil ata2: dev 0 ATA, max UDMA/133, 490234752 sectors: lba48 ata2: dev 0 configured for UDMA/100 scsi1 : sata_sil ata3: no device found (phy stat 00000000) scsi2 : sata_sil ata4: no device found (phy stat 00000000) scsi3 : sata_sil Vendor: ATA Model: Maxtor 6V250F0 Rev: VA11 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: Maxtor 6V250F0 Rev: VA11 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) SCSI device sda: drive cache: write back SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) SCSI device sda: drive cache: write back sda: sda1 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB) SCSI device sdb: drive cache: write back sdb: Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 usbmon: debugfs is not available driver fsl-usb2-mph, $Revision: 1.11 $ fsl-usb2-mph fsl-usb2-mph.1: new USB bus registered, assigned bus number 1 fsl-usb2-mph fsl-usb2-mph.1: park 0 fsl-usb2-mph fsl-usb2-mph.1: USB 0.0 initialized, EHCI 1.00, driver $Revision: 1.11 $ usb usb1: Product: fsl usb20 usb usb1: Manufacturer: Linux 2.6.13.4 fsl-usb2-mph usb usb1: SerialNumber: fsl-usb2-mph.1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27) usb 1-1: new high speed USB device using fsl-usb2-mph and address 2 usb 1-1: Product: USB2.0 Hub hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected usbcore: registered new driver rtl8150 usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 i2c /dev entries driver md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 448.000 MB/sec 8regs_prefetch: 396.000 MB/sec 32regs : 484.000 MB/sec 32regs_prefetch: 528.000 MB/sec raid5: using function: 32regs_prefetch (528.000 MB/sec) md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 3.38 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 eth0: PHY is Intellon 6xMX Module (2834) IP-Config: Gateway not on directly connected network. md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. md: Unknown device name: sdc md: Loading md0: /dev/sda md: bind md: sdb has different UUID to sda md: sdb has different UUID to sda md: export_rdev(sdb) raid1: raid set md0 active with 1 out of 2 mirrors RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 112k init Setting the hostname to mpc8349itx-min-fs Mounting filesystems rootfs / rootfs rw 0 0 /dev/root / ext2 rw 0 0 proc /proc proc rw,nodiratime 0 0 rwfs /mnt/rwfs tmpfs rw 0 0 Starting syslogd and klogd Running depmod Setting up networking on loopback device: Setting up networking on eth0: udhcpc (v0.9.9-pre) started Sending discover... Sending select for 192.168.0.8... Lease of 192.168.0.8 obtained, lease time 864000 deleting routers SIOCDELRT: No such process adding dns 212.27.40.240 adding dns 212.27.40.241 Starting inetd: Welcome to Freescale Semiconductor Embedded Linux Environment !!!!! WARNING !!!!!!! The default password for the root account is: root please change this password using the 'passwd' command and then edit this message (/etc/issue) to remove this message mpc8349itx-min-fs login: --------------------------------------------------------------- Boot linux 2.6.26 with libata.dma=0 ---------------------------------------------------------------- Using MPC834x ITX machine description Linux version 2.6.26 (olivier@olivier-desktop) (gcc version 4.2.1 (Sourcery G++ Lite 4.2-82)) #35 Tue Jul 29 16:55:34 CEST 2008 Found initrd at 0xcf829000:0xcff74b4a Found MPC83xx PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0 PCI host bridge /pci@e0008500 (primary) ranges: MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 Prefetch MEM 0x0000000090000000..0x000000009fffffff -> 0x0000000090000000 IO 0x00000000e2000000..0x00000000e2ffffff -> 0x0000000000000000 Found MPC83xx PCI host bridge at 0x00000000e0008600. Firmware bus number: 0->0 PCI host bridge /pci@e0008600 ranges: MEM 0x00000000a0000000..0x00000000afffffff -> 0x00000000a0000000 Prefetch MEM 0x00000000b0000000..0x00000000bfffffff -> 0x00000000b0000000 IO 0x00000000e3000000..0x00000000e3ffffff -> 0x0000000000000000 Zone PFN ranges: DMA 0 -> 65536 Normal 65536 -> 65536 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 65536 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: root=/dev/ram ramdisk_size=80000 rw ip=192.168.0.20:192.168.0.42:192.168.1.254:255.255.255.0:PowerQUICC:eth0:off console=ttyS1,115200 libata.dma=0 libata.force=pio7 IPIC (128 IRQ sources) at fbffc700 PID hash table entries: 1024 (order: 10, 4096 bytes) clocksource: timebase mult[3c00001] shift[22] registered Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 248440k/262144k available (3356k kernel code, 13384k reserved, 116k data, 100k bss, 168k init) SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Mount-cache hash table entries: 512 net_namespace: 192 bytes xor: measuring software checksum speed 8regs : 405.000 MB/sec 8regs_prefetch: 385.000 MB/sec 32regs : 485.000 MB/sec 32regs_prefetch: 471.000 MB/sec xor: using function: 32regs (485.000 MB/sec) NET: Registered protocol family 16 PCI: Probing PCI hardware SCSI subsystem initialized ata: failed to parse force parameter "pio7" (unknown value) usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 7470k freed msgmni has been set to 500 async_tx: api initialized (async) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 18) is a 16550A serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 19) is a 16550A console [ttyS1] enabled brd: module loaded loop: module loaded eth0: Gianfar Ethernet Controller Version 1.2, 08:00:3e:03:01:11 eth0: Running with NAPI enabled eth0: 256/256 RX/TX BD ring size eth1: Gianfar Ethernet Controller Version 1.2, 08:00:3e:03:01:12 eth1: Running with NAPI enabled eth1: 256/256 RX/TX BD ring size Fixed MDIO Bus: probed Driver 'sd' needs updating - please use bus_type methods sata_sil 0000:00:10.0: enabling device (0000 -> 0003) sata_sil 0000:00:10.0: cache line size not set. Driver may not function sata_sil 0000:00:10.0: Applying R_ERR on DMA activate FIS errata fix scsi0 : sata_sil scsi1 : sata_sil scsi2 : sata_sil scsi3 : sata_sil ata1: SATA max UDMA/100 mmio m1024@0x90000000 tf 0x90000080 irq 22 ata2: SATA max UDMA/100 mmio m1024@0x90000000 tf 0x900000c0 irq 22 ata3: SATA max UDMA/100 mmio m1024@0x90000000 tf 0x90000280 irq 22 ata4: SATA max UDMA/100 mmio m1024@0x90000000 tf 0x900002c0 irq 22 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-7: Maxtor 6V250F0, VA111900, max UDMA/133 ata1.00: 490234752 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for PIO4 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata2.00: ATA-7: Maxtor 6V250F0, VA111900, max UDMA/133 ata2.00: 490234752 sectors, multi 0: LBA48 NCQ (depth 0/32) ata2.00: configured for PIO4 ata3: SATA link down (SStatus 0 SControl 310) ata4: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA Maxtor 6V250F0 VA11 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 490234752 512-byte hardware sectors (251000 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: Direct-Access ATA Maxtor 6V250F0 VA11 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sd 1:0:0:0: [sdb] Attached SCSI disk fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 39, io base 0xe0022000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usb 1-1: new high speed USB device using fsl-ehci and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i2c /dev entries driver S08QG8:Version 0.3 - 09 Jan 2008 md: raid1 personality registered for level 1 raid6: int32x1 35 MB/s raid6: int32x2 54 MB/s raid6: int32x4 84 MB/s raid6: int32x8 99 MB/s raid6: using algorithm int32x8 (99 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 md: multipath personality registered for level -4 md: faulty personality registered for level -5 TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. drivers/rtc/hctosys.c: unable to open rtc device (rtc0) IP-Config: Gateway not on directly connected network. md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 168k init PHY: 0:01 - Link is Up - 100/Full Setting the hostname to oze-systems Mounting filesystems rootfs / rootfs rw 0 0 /dev/root / ext2 rw 0 0 proc /proc proc rw 0 0 rwfs /mnt/rwfs tmpfs rw,size=512k 0 0 VFS: Can't find an ext2 filesystem on dev sda1. mount: wrong fs EXT2-fs: unable to read superblock type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so mount: wrong fs type, bad option, bad superblock on /dev/md0, missing codepage or helper program, or other error (could this be the IDE device where you in fact use ide-scsi so that sr0 or sda or so is needed?) In some cases useful info is found in syslog - try dmesg | tail or so Running sysctl Setting up networking on loopback device: Setting up networking on eth0: udhcpc (v0.9.9-pre) started udhcpc[815]: udhcpc (v0.9.9-pre) started Sending discover... udhcpc[815]: Sending discover... Sending select for 192.168.0.8... udhcpc[815]: Sending select for 192.168.0.8... Lease of 192.168.0.8 obtained, lease time 864000 udhcpc[815]: Lease of 192.168.0.8 obtained, lease time 864000 deleting routers SIOCDELRT: No such process adding dns 212.27.40.240 adding dns 212.27.40.241 Setting up networking on eth1: eth1: 0:01 already attached eth1: Could not attach to PHY SIOCSIFFLAGS: Device or resource busy Starting inetd: Starting the dropbear ssh server: Setting time from ntp server: ntp.cs.strath.ac.uk Welcome to OZE oze-systems login: