This is a clean up patch that includes the following changes: -It removes some macro definitions that are only used once with the actual code. -Some comments were added to clarify the code based on feedback from the community. -The write_pm_cntrl() and set_count_mode() were passed a structure element from a global variable. The argument was removed so the functions now just operate on the global directly. -The set_pm_event() function call in the cell_virtual_cntr() routine was moved to a for-loop before the for_each_cpu loop Signed-off-by: Carl Love Signed-off-by: Maynard Johnson Index: linux-2.6.19-rc6-arnd1+patches/arch/powerpc/oprofile/op_model_cell.c =================================================================== --- linux-2.6.19-rc6-arnd1+patches.orig/arch/powerpc/oprofile/op_model_cell.c 2006-11-24 11:34:45.048430752 -0600 +++ linux-2.6.19-rc6-arnd1+patches/arch/powerpc/oprofile/op_model_cell.c 2006-11-27 11:45:00.737473968 -0600 @@ -41,8 +41,12 @@ #define PPU_CYCLES_EVENT_NUM 1 /* event number for CYCLES */ #define CBE_COUNT_ALL_CYCLES 0x42800000 /* PPU cycle event specifier */ -#define NUM_THREADS 2 -#define VIRT_CNTR_SW_TIME_NS 100000000 // 0.5 seconds +#define NUM_THREADS 2 /* number of physical threads in + * physical processor + */ +#define NUM_TRACE_BUS_WORDS 4 +#define NUM_INPUT_BUS_WORDS 2 + struct pmc_cntrl_data { unsigned long vcntr; @@ -94,14 +98,6 @@ } pm_regs; -#define GET_SUB_UNIT(x) ((x & 0x0000f000) >> 12) -#define GET_BUS_WORD(x) ((x & 0x000000f0) >> 4) -#define GET_BUS_TYPE(x) ((x & 0x00000300) >> 8) -#define GET_POLARITY(x) ((x & 0x00000002) >> 1) -#define GET_COUNT_CYCLES(x) (x & 0x00000001) -#define GET_INPUT_CONTROL(x) ((x & 0x00000004) >> 2) - - static DEFINE_PER_CPU(unsigned long[NR_PHYS_CTRS], pmc_values); static struct pmc_cntrl_data pmc_cntrl[NUM_THREADS][NR_PHYS_CTRS]; @@ -129,8 +125,8 @@ static u32 ctr_enabled; -static unsigned char trace_bus[4]; -static unsigned char input_bus[2]; +static unsigned char trace_bus[NUM_TRACE_BUS_WORDS]; +static unsigned char input_bus[NUM_INPUT_BUS_WORDS]; /* * Firmware interface functions @@ -221,24 +217,32 @@ pm_regs.pm07_cntrl[ctr] = 0; } - bus_word = GET_BUS_WORD(unit_mask); - bus_type = GET_BUS_TYPE(unit_mask); - count_cycles = GET_COUNT_CYCLES(unit_mask); - polarity = GET_POLARITY(unit_mask); - input_control = GET_INPUT_CONTROL(unit_mask); + bus_word = (unit_mask & 0x000000f0) >> 4; + bus_type = (unit_mask & 0x00000300) >> 8; + count_cycles = unit_mask & 0x00000001; + polarity = (unit_mask & 0x00000002) >> 1; + input_control = (unit_mask & 0x00000004) >> 2; signal_bit = (event % 100); p = &(pm_signal[ctr]); p->signal_group = event / 100; p->bus_word = bus_word; - p->sub_unit = unit_mask & 0x0000f000; + p->sub_unit = (unit_mask & 0x0000f000) >> 12; pm_regs.pm07_cntrl[ctr] = 0; - pm_regs.pm07_cntrl[ctr] |= PM07_CTR_COUNT_CYCLES(count_cycles); - pm_regs.pm07_cntrl[ctr] |= PM07_CTR_POLARITY(polarity); - pm_regs.pm07_cntrl[ctr] |= PM07_CTR_INPUT_CONTROL(input_control); - + pm_regs.pm07_cntrl[ctr] |= (count_cycles & 1) << 23; + pm_regs.pm07_cntrl[ctr] |= (polarity & 1) << 24; + pm_regs.pm07_cntrl[ctr] |= (input_control & 1) << 25; + + /* Some of the islands signal selection is based on 64 bit words. + * The debug bus words are 32 bits, the input words to the performance + * counters are defined as 32 bits. Need to convert the 64 bit island + * specification to the appropriate 32 input bit and bus word for the + * performance counter event selection. See the CELL Performance + * monitoring signals manual and the Perf cntr hardware descriptions + * for the details. + */ if (input_control == 0) { if (signal_bit > 31) { signal_bit -= 32; @@ -253,18 +257,18 @@ if ((bus_type == 1) && p->signal_group >= 50) bus_type = 0; - pm_regs.pm07_cntrl[ctr] |= PM07_CTR_INPUT_MUX(signal_bit); + pm_regs.pm07_cntrl[ctr] |= (signal_bit & 0x3F) << 26; } else { pm_regs.pm07_cntrl[ctr] = 0; p->bit = signal_bit; } - for (i = 0; i < 4; i++) { + for (i = 0; i < NUM_TRACE_BUS_WORDS; i++) { if (bus_word & (1 << i)) { pm_regs.debug_bus_control |= (bus_type << (31 - (2 * i) + 1)); - for (j = 0; j < 2; j++) { + for (j = 0; j < NUM_INPUT_BUS_WORDS; j++) { if (input_bus[j] == 0xff) { input_bus[j] = i; pm_regs.group_control |= @@ -278,52 +282,58 @@ ; } -static void write_pm_cntrl(int cpu, struct pm_cntrl *pm_cntrl) +static void write_pm_cntrl(int cpu) { - /* Oprofile will use 32 bit counters, set bits 7:10 to 0 */ + /* Oprofile will use 32 bit counters, set bits 7:10 to 0 + * pmregs.pm_cntrl is a global + */ + u32 val = 0; - if (pm_cntrl->enable == 1) + if (pm_regs.pm_cntrl.enable == 1) val |= CBE_PM_ENABLE_PERF_MON; - if (pm_cntrl->stop_at_max == 1) + if (pm_regs.pm_cntrl.stop_at_max == 1) val |= CBE_PM_STOP_AT_MAX; - if (pm_cntrl->trace_mode == 1) - val |= CBE_PM_TRACE_MODE_SET(pm_cntrl->trace_mode); + if (pm_regs.pm_cntrl.trace_mode == 1) + val |= CBE_PM_TRACE_MODE_SET(pm_regs.pm_cntrl.trace_mode); - if (pm_cntrl->freeze == 1) + if (pm_regs.pm_cntrl.freeze == 1) val |= CBE_PM_FREEZE_ALL_CTRS; /* Routine set_count_mode must be called previously to set * the count mode based on the user selection of user and kernel. */ - val |= CBE_PM_COUNT_MODE_SET(pm_cntrl->count_mode); + val |= CBE_PM_COUNT_MODE_SET(pm_regs.pm_cntrl.count_mode); cbe_write_pm(cpu, pm_control, val); } static inline void -set_count_mode(u32 kernel, u32 user, struct pm_cntrl *pm_cntrl) +set_count_mode(u32 kernel, u32 user) { /* The user must specify user and kernel if they want them. If - * neither is specified, OProfile will count in hypervisor mode + * neither is specified, OProfile will count in hypervisor mode. + * pm_regs.pm_cntrl is a global */ if (kernel) { if (user) - pm_cntrl->count_mode = CBE_COUNT_ALL_MODES; + pm_regs.pm_cntrl.count_mode = CBE_COUNT_ALL_MODES; else - pm_cntrl->count_mode = CBE_COUNT_SUPERVISOR_MODE; + pm_regs.pm_cntrl.count_mode = + CBE_COUNT_SUPERVISOR_MODE; } else { if (user) - pm_cntrl->count_mode = CBE_COUNT_PROBLEM_MODE; + pm_regs.pm_cntrl.count_mode = CBE_COUNT_PROBLEM_MODE; else - pm_cntrl->count_mode = CBE_COUNT_HYPERVISOR_MODE; + pm_regs.pm_cntrl.count_mode = + CBE_COUNT_HYPERVISOR_MODE; } } static inline void enable_ctr(u32 cpu, u32 ctr, u32 * pm07_cntrl) { - pm07_cntrl[ctr] |= PM07_CTR_ENABLE(1); + pm07_cntrl[ctr] |= CBE_PM_CTR_ENABLE; cbe_write_pm07_control(cpu, ctr, pm07_cntrl[ctr]); } @@ -365,6 +375,14 @@ hdw_thread = 1 ^ hdw_thread; next_hdw_thread = hdw_thread; + for (i = 0; i < num_counters; i++) + /* There are some per thread events. Must do the + * set event, for the thread that is being started + */ + set_pm_event(i, + pmc_cntrl[next_hdw_thread][i].evnts, + pmc_cntrl[next_hdw_thread][i].masks); + /* The following is done only once per each node, but * we need cpu #, not node #, to pass to the cbe_xxx functions. */ @@ -385,12 +403,13 @@ == 0xFFFFFFFF) /* If the cntr value is 0xffffffff, we must * reset that to 0xfffffff0 when the current - * thread is restarted. This will generate a new - * interrupt and make sure that we never restore - * the counters to the max value. If the counters - * were restored to the max value, they do not - * increment and no interrupts are generated. Hence - * no more samples will be collected on that cpu. + * thread is restarted. This will generate a + * new interrupt and make sure that we never + * restore the counters to the max value. If + * the counters were restored to the max value, + * they do not increment and no interrupts are + * generated. Hence no more samples will be + * collected on that cpu. */ cbe_write_ctr(cpu, i, 0xFFFFFFF0); else @@ -410,9 +429,6 @@ * Must do the set event, enable_cntr * for each cpu. */ - set_pm_event(i, - pmc_cntrl[next_hdw_thread][i].evnts, - pmc_cntrl[next_hdw_thread][i].masks); enable_ctr(cpu, i, pm_regs.pm07_cntrl); } else { @@ -465,8 +481,7 @@ pm_regs.pm_cntrl.trace_mode = 0; pm_regs.pm_cntrl.freeze = 1; - set_count_mode(sys->enable_kernel, sys->enable_user, - &pm_regs.pm_cntrl); + set_count_mode(sys->enable_kernel, sys->enable_user); /* Setup the thread 0 events */ for (i = 0; i < num_ctrs; ++i) { @@ -498,10 +513,10 @@ pmc_cntrl[1][i].vcntr = i; } - for (i = 0; i < 4; i++) + for (i = 0; i < NUM_INPUT_BUS_WORDS; i++) trace_bus[i] = 0xff; - for (i = 0; i < 2; i++) + for (i = 0; i < NUM_INPUT_BUS_WORDS; i++) input_bus[i] = 0xff; /* Our counters count up, and "count" refers to @@ -560,7 +575,7 @@ cbe_write_pm(cpu, pm_start_stop, 0); cbe_write_pm(cpu, group_control, pm_regs.group_control); cbe_write_pm(cpu, debug_bus_control, pm_regs.debug_bus_control); - write_pm_cntrl(cpu, &pm_regs.pm_cntrl); + write_pm_cntrl(cpu); for (i = 0; i < num_counters; ++i) { if (ctr_enabled & (1 << i)) { @@ -602,7 +617,7 @@ } } - cbe_clear_pm_interrupts(cpu); + cbe_get_and_clear_pm_interrupts(cpu); cbe_enable_pm_interrupts(cpu, hdw_thread, interrupt_mask); cbe_enable_pm(cpu); } @@ -672,7 +687,7 @@ cbe_disable_pm(cpu); - interrupt_mask = cbe_clear_pm_interrupts(cpu); + interrupt_mask = cbe_get_and_clear_pm_interrupts(cpu); /* If the interrupt mask has been cleared, then the virt cntr * has cleared the interrupt. When the thread that generated Index: linux-2.6.19-rc6-arnd1+patches/arch/powerpc/platforms/cell/pmu.c =================================================================== --- linux-2.6.19-rc6-arnd1+patches.orig/arch/powerpc/platforms/cell/pmu.c 2006-11-24 11:34:44.880456288 -0600 +++ linux-2.6.19-rc6-arnd1+patches/arch/powerpc/platforms/cell/pmu.c 2006-11-27 11:45:00.739473664 -0600 @@ -345,18 +345,12 @@ * Enabling/disabling interrupts for the entire performance monitoring unit. */ -u32 cbe_query_pm_interrupts(u32 cpu) -{ - return cbe_read_pm(cpu, pm_status); -} -EXPORT_SYMBOL_GPL(cbe_query_pm_interrupts); - -u32 cbe_clear_pm_interrupts(u32 cpu) +u32 cbe_get_and_clear_pm_interrupts(u32 cpu) { /* Reading pm_status clears the interrupt bits. */ - return cbe_query_pm_interrupts(cpu); + return cbe_read_pm(cpu, pm_status); } -EXPORT_SYMBOL_GPL(cbe_clear_pm_interrupts); +EXPORT_SYMBOL_GPL(cbe_get_and_clear_pm_interrupts); void cbe_enable_pm_interrupts(u32 cpu, u32 thread, u32 mask) { @@ -371,7 +365,7 @@ void cbe_disable_pm_interrupts(u32 cpu) { - cbe_clear_pm_interrupts(cpu); + cbe_get_and_clear_pm_interrupts(cpu); cbe_write_pm(cpu, pm_status, 0); } EXPORT_SYMBOL_GPL(cbe_disable_pm_interrupts); Index: linux-2.6.19-rc6-arnd1+patches/include/asm-powerpc/cell-pmu.h =================================================================== --- linux-2.6.19-rc6-arnd1+patches.orig/include/asm-powerpc/cell-pmu.h 2006-11-24 11:34:52.744459720 -0600 +++ linux-2.6.19-rc6-arnd1+patches/include/asm-powerpc/cell-pmu.h 2006-11-27 11:45:22.987553552 -0600 @@ -89,8 +89,7 @@ extern void cbe_enable_pm_interrupts(u32 cpu, u32 thread, u32 mask); extern void cbe_disable_pm_interrupts(u32 cpu); -extern u32 cbe_query_pm_interrupts(u32 cpu); -extern u32 cbe_clear_pm_interrupts(u32 cpu); +extern u32 cbe_get_and_clear_pm_interrupts(u32 cpu); extern void cbe_sync_irq(int node); /* Utility functions, macros */ @@ -103,11 +102,4 @@ #define CBE_COUNT_PROBLEM_MODE 2 #define CBE_COUNT_ALL_MODES 3 -/* Macros for the pm07_control registers. */ -#define PM07_CTR_INPUT_MUX(x) (((x) & 0x3F) << 26) -#define PM07_CTR_INPUT_CONTROL(x) (((x) & 1) << 25) -#define PM07_CTR_POLARITY(x) (((x) & 1) << 24) -#define PM07_CTR_COUNT_CYCLES(x) (((x) & 1) << 23) -#define PM07_CTR_ENABLE(x) (((x) & 1) << 22) - #endif /* __ASM_CELL_PMU_H__ */